Difference between revisions of "Troubleshooting"
(→That didn't work, now what?)
|Line 157:||Line 157:|
*[[Managing your monthly DSL bandwidth usage]]
*[[Managing your monthly DSL bandwidth usage]]
Revision as of 10:38, 7 December 2016
This page provides some troubleshooting tips and advice if your DSL service stops working.
- 1 If it was working and now is not
- 2 Start-up problems and chronic problems
- 3 Sagemcom modem: you're getting a "Welcome to Bell" page
- 4 See also
If it was working and now is not
If your service was working and is not working now, and you have not changed anything, chances are that the problem is a network outage. The best thing to do is wait to see if the problem resolves itself. Generally network problems will be solved within an hour. To check network status, go to http://www.bell.ca/Bell_Internet#
If you know another NCF DSL member you can ask them if their service is working.
Sometimes your modem may not notice that the network is back up. Try power-cycling your modem to force it to look for the network on restart.
Start-up problems and chronic problems
If your service is chronically sub-optimal, below are some possible problems and possible solutions.
Background information about DSL
The low-frequency end of your phone line is reserved for voice signals. DSL works by using higher frequencies. Line filters keep the DSL signals from affecting non-DSL devices and also keep those devices from interfering with the DSL portion of the spectrum.
When your modem detects the DSL signal, it tries to synchronize with it (get in sync). If it can do this, the modem is said to be in sync and the DSL/Broadband light will be green.
When a DSL signal is detected, the modem assesses the power spectrum of the line and decides how much bandwidth is available. If the line quality is poor, the modem will operate at lower speeds to reduce the number of errors. For best performance, good line quality is essential.
DSL signals weaken with distance, so DSL works best when your location is close to Bell equipment (DSLAM). Bell invests in DSLAM equipment in an area depending on many factors. If they have not yet installed a DSLAM near your location, they may not be able to offer as high bandwidth as in other locations, even ones nearby.
If performance (e.g., speed tests) on your line is significantly worse from that of your neighbours, chances are good that something is non-optimal at your location or on your line.
If you get expected speeds in the morning and late at night, but experience slower speeds in the evenings and on weekends then the likely culprit is network congestion. NCF has investigated the problem and found that there was network congestion between the NCF network and the Bell Network at the aggregation point. We implemented a solution and we will continue to monitor it and make further adjustments as necessary.
- DSL speed
- Stages of DSL connection-making (learn how it should go)
- About DSL modem lights (what the lights can tell you)
General strategies for DSL problem-solving
- Check the lights on your modem - the lights can tell you a lot of useful information.
- Check your installation. Are your wires connected and plugs seated securely?
- Check the NCF DSL help discussion group to see how other members have solved the problem, or post a description of your problem so that other members can help. This is often faster than asking the NCF office because NCF members are often able to answer around the clock! Besides, one of NCF's founding motivations was to provide a means for people to help people.
- Check the internet for information using a search engine. There are lots of web pages on diagnosing and treating DSL problems.
- If you are pretty sure it is a problem with your phone line, please send a message to the NCF office (using the Office Message button on the Help page). Or if you hear static and noise on your voice calls (assuming you have voice service from Bell on the same line as your DSL), you can have Bell address that by dialing 611, it will help your DSL quality too.
- NCF is not-for-profit association owned by its members (including you), and the level of office support versus DSL price is something members decide as a group. In general, NCF members prefer to solve problems themselves or with the help of other members rather than pay more. (see Help page)
- Bell offers a for-fee service for "line care", which costs about $100 for a year of coverage. Bell will investigate all problems inside or outside your location relating to DSL and voice for a year. This could be attractive for people with marginal DSL service, especially for the initial first year to get DSL working at your location.
Testing at the demarcation point
Before opening a ticket with Bell and possibly incurring a fee, you will want to make sure the problem is not with your inside house wiring. You can do this by plugging your DSL modem directly into the Network interface device box or demarcation point, which bypasses your wiring and connects you directly to Bell's lines.
If the problem is solved, the issue is with your inside wiring and you will want to hire a licensed contractor to look into it for you.
If the problem persists, it is likely the issue is with Bell's wires leading into your home. You may wish to ask the NCF office to open a ticket with Bell, who will send a technician to make a service call.
If you do not have DSL connection (no DSL or internet modem lights), your connection is intermittent or you experience low speed
Here are some possible causes:
- DSL modem is connected to the phone line via a line filter
- Solution: The DSL modem must be directly connected to the phone line, without a line filter, remove any filter.
- Modem not connected to working phone jack or to a line with DSL service
- Solution: If you have multiple phone lines at your location, be sure the modem is connected to the line with DSL service. If the line also has voice service (i.e., is not 'dry DSL'), there should be dial-tone if you plug in a phone at that jack.
- Telephone(s) or other devices not filtered on the same phone line
- Solution: All devices (other than the DSL modem itself) must be connected via a line filter (otherwise they may interfere with the DSL signal). Install filters or disconnect the other devices from the phone line.
- Outside line issues: Noise on your phone line. If you hear cracks, static, etc on your phone line, this can interfere with your DSL signal too
- Solution: Call 611 to report the problem to Bell. Tell them about the voice quality on your line being poor due to cracks, pops & static sounds. Probably best not to mention DSL, just focus on voice quality issues.
- Defective filter(s). If the DSL modem works well with all other devices temporarily unplugged from your line, maybe one of those devices has a defective filter
- Solution: Try to figure out which filter is defective by plugging the devices in one at a time. If one is found to be defective, replace it.
- Faulty inside wiring / phone jack(s). If your problems appear after adding a new phone or other device, or changing the wiring in your house, those changes are likely the cause of problems
- Solution: Repair your inside wiring. If unsuccessful, Bell offers a charge-by-the-hour service to find problems within your residence, call 611 to arrange for assistance.
- Distance from DSL service exceeds maximum distance. If you've never been able to obtain sync, maybe your location is too far from the nearest Bell service point
- Solution: NCF can work with Bell to assess this. Contact NCF via the Help page.
- Electrical interference from AM radio, halogen lights, audio speakers, power supplies
- Solution: Locate the modem away from sources of electrical interference. Use shielded twisted pair cabling from the modem to the wall jack.
- Apartment intercom interference
- Some older-style apartment door intercoms actually cut into the phone line system and can interfere with DSL signals, causing a loss of connectivity. Many are being replaced by more modern systems that act as telephones and dial your home or cell phone number and won't interfere with DSL. If you determine this is the problem try discussing this with your landlord.
- Using low-quality phone wire between the phone jack and modem
- Solution: It is best to use just the phone line that was provide by the modem. If you need an extension to reach a jack, be sure it is high quality. Instead, consider using a longer ethernet cable to reach the computer (or use wireless instead).
- Modem overheating.
- Solution: Ensure the ventilation ports, usually located on the bottom of the modem are clear. Try mounting the modem on its side (vertically), on a hard surface or raised up on blocks so that airflow is optimal. If it was operating at a normal temperature and is now overheating it is likely about to fail and requires replacing.
- Spider webs
- Solution: Check that your telephone junction boxes are free of spider webs (they can conduct and interfere with short range, high frequency signals, says a local engineer who worked on early DSL-like hardware development).
- Wet weather, especially in the spring
- Solution: Often wet weather, especially during the spring melt, causes phone line performance to degrade (water gets in and temporarily changes the electrical characteristics of the line). Lines are supposed to be waterproof, but with age that can degrade. Such problems often 'dry up' as conditions improve.
- Failing modem
- Solution: Modems rarely just quit dead, many models seem to have failure modes where they keep working, but don't provide a good stable connection. You can borrow a "loaner modem" from the NCF office (deposit required). The staff will set it up with your account information and password so that you can just take it home and plug it in. If this solves problem then chances are that the problem is that your own modem is failing. If this does not solve the problem then it will rule out your modem as the cause of the issue.
- Wireless issues
- For wireless issues have a look at about wireless.
That didn't work, now what?
Nothing works? Try:
- Searching the internet for ideas
- DNS Problems see Google's tips
- Posting to the NCF DSL discussion group
- If all those fail, try describing your problem to the NCF office via the Office Message system on the Help page.
Sagemcom modem: you're getting a "Welcome to Bell" page
If this occurs, members see a Bell splash page when they enter their browser. The page requests a login (with Bell credentials) which our members can't complete.
No other modem configuration details are disturbed other than the Internet login.
The root cause is not known, but may involve some type of reset signal on the DSL line.
The correct credentials need to be put back into the modem. Those credentials are:
Password: ncf.... (typically, a 12 alpha-numeric characters string)
That can be done in at least 3 ways:
- on your own – the instructions for this are given below
- NCF staff can walk you through the process over the phone
- you can bring the modem into the office and we'll deal with it
Instructions to change the Internet logon values
Here are the instructions to recover full Internet access from the Sagemcom modem:
- connect an Ethernet cable between a PC and the modem
- Start up a browser on the PC
- In the address bar, type '192.168.2.1' (without the quotation marks), press Enter
- you should see a login window
- for the user, type: 'admin' (without the quotation marks), and for the password type: <your 12 character NCF DSL password: ncf...>
- you should now see a window labeled 'Connection Hub'
- In the menu on the Left Hand side of the window, click on the 'Internet' field
- you should now see a window with a userid and password fields – the userid will show 'sc.......'
- in the user field, enter your NCF ID followed by '@ncf.ca' (e.g., firstname.lastname@example.org)
- in the password field, enter your NCF DSL password (your 12 character NCF DSL password: ncf...)
- click the 'Save' button at the bottom of the window
- when you see the 'Settings Saved' message, the Internet light (the one with the @ sign) should start to blink red and then turn blue - this may take some time.
Access should be restored and your work is done.
It's possible that a power cycle may be required to get the modem to recognize the configuration change so if a "Save" doesn't restore your Internet, try that.
- NCF DSL discussion group Draw on the expertise of fellow NCF members
- About wireless
- DSL speed
- Speed test (DSL) How to do a speed test of your DSL service
- Line stats (DSL) How to obtain and interpret line stats from your DSL modem
- SpeedTouch 516 and 585 on ADSL2+
- Computer Help
- Managing your monthly DSL bandwidth usage
- Broken internet connection on Windows 10