Difference between revisions of "Troubleshooting (DSL)"
(→'No sync', 'intermittent sync', 'poor performance', and 'low speed')
(→Didn't work, now what?: formatting as a list)
|Line 79:||Line 79:|
=== Didn't work, now what? ===
=== Didn't work, now what? ===
Nothing works? Try
the internet for ideas
the [http://www.ncf.ca/ncf/dg/index.jsp?dg=82 NCF DSL discussion group]
If all those fail, try describing your problem to the NCF office via the [http://help.ncf.ca Help page].
== Related links ==
== Related links ==
Revision as of 18:32, 21 December 2011
This page provides some troubleshooting tips and advice if your DSL service stops working.
If it was working and now is not
If your service was working and now is not working and you have not changed anything, chances are that the problem is a network outage. The best thing to do is wait to see if the problem resolves itself. Generally network problems will be solved within an hour.
If you know another NCF DSL member you can ask them if their service is working.
Sometimes your modem may not notice that the network is back up. Try power-cycling your modem to force it to look for the network on restart.
Start-up problems and chronic problems
If your service is chronically sub-optimal, below are some possible problems and possible solutions.
Background information about DSL
The low-frequency end of your phone line is reserved for voice signals. DSL works by using higher frequencies. Line filters keep the DSL signals from affecting non-DSL devices and also keep those devices from interfering with the DSL portion of the spectrum.
When your modem detects the DSL signal, it tries to synchronize with it (get in sync). If it can do this, the modem is said to be in sync and the DSL/Broadband light will be green.
When a DSL signal is detected, the modem assesses the power spectrum of the line and decides how much bandwidth is available. If the line quality is poor, the modem will operate at lower speeds to reduce the number of errors. For best performance, good line quality is essential.
DSL signals weaken with distance, so DSL works best when your location is close to Bell equipment (DSLAM). Bell invests in DSLAM equipment in an area depending on many factors. If they have not yet installed a DSLAM near your location, they may not be able to offer as high bandwidth as in other locations, even ones nearby.
If performance (eg., speed tests) on your line is significantly worse from that of your neighbours, chances are good that something is non-optimal at your location or on your line.
- Stages of DSL connection-making (learn how it should go)
- About DSL modem lights (what the lights can tell you)
General strategies for DSL problem-solving
- Check the lights on your modem (what the lights can tell you)
- Check your installation
- Check the NCF DSL help discussion group to see how other members have solved the problem, or post a description of your problem so that other members can help. This is often faster than asking the NCF office because NCF members are often able to answer around the clock! Besides, one of NCF's founding motivations was to provide a means for people to help people.
- Check the internet for information using a search engine. There are lots of web pages on diagnosing and treating DSL problems.
- If you are pretty sure it is a problem with your phone line, please send a message to the NCF office (using the Office Message button on the Help page). Or if you hear static and noise on your voice calls (assuming you have voice service from Bell on the same line as your DSL), you can have Bell address that by dialing 611 and it will help your DSL quality too.
- NCF is not-for-profit association owned by its members (including you), and the level of office support versus DSL price is something members decide as a group. In general, NCF members prefer to solve problems themselves or with the help of other members rather than pay more. (see Help page)
- Bell offers a for-fee service for "line care", which costs about $100 for a year of coverage. Bell will investigate all problems inside or outside your location relating to DSL and voice for a year. This could be attractive for people with marginal DSL service, especially for the initial first year to get DSL working at your location.
Generally the approach is to try the best possible arrangement for your modem, with no other devices on your phone line and the modem as close as possible to where your phone line comes into your house (the demarcation point), away from all sources of electrical interference, to test if that improves quality. f that works, then something about your normal configuration of devices is creating a problem. Otherwise, maybe it is an external (Bell) wiring problem.
'No sync', 'intermittent sync', 'poor performance', and 'low speed'
Here are some possible causes of 'no sync', 'intermittent sync', 'poor performance', and 'low speed':
- DSL modem is connected to the phone line via a line filter
- Possible solution: The DSL modem must be directly connected to the phone line, without a line filter.
- Modem not connected to working phone jack to a line with DSL service.
- Possible solution: If you have multiple phone lines at your location, be sure the modem is connected to the line with DSL service. If the line also has voice service (ie., is not 'dry DSL'), there should be dial-tone if you plug in a phone at that jack.
- Telephone(s) or other devices not filtered on the same phone line.
- Possible solution: All devices (other than the DSL modem itself) must be connected via a line filter (otherwise they may interfere with the DSL signal). Install filters or disconnect the other devices from the phone line.
- Outside line issues: Noise on your phone line. If you hear cracking, static, etc on your phone line, this can interfere with your DSL signal too.
- Possible solution: Call 611 to report the problem to Bell Canada. Tell them about the voice quality on your line being poor due to cracks & pops & static sounds. (Probably best not to mention DSL, just focus on voice quality issues.)
- Defective filter(s). If the DSL modem works well with all other devices temporarily unplugged from your line, maybe one of those devices has a defective filter.
- Possible solution: Try to figure out which filter is defective by plugging the devices in one at a time. If one is found to be defective, replace it.
- Faulty inside wiring / phone jack(s). If your problems appear after adding a new phone or other device, or changing the wiring in your house, those changes are likely the cause of problems.
- Possible solution: Try to repair your inside wiring. If unsuccessful, Bell Canada offers a charge-by-the-hour service to find problems within your residence, call 611 to arrange for assistance.
- Distance from DSL service exceeds maximum distance. If you've never been able to obtain sync, maybe your location is too far from the nearest Bell service point.
- Possible solution: NCF can work with Bell to assess this. Contact NCF via the Help page.
- Electrical interference from AM radio, halogen lights, audio speakers, power supplies.
- Possible solution: Locate the modem away from sources of electrical interference. Use shielded twisted pair cabling from the modem to the wall jack.
- Using low-quality phone wire between the phone jack and modem.
- Possible solution: It is best to use just the phone line that was provide by the modem. If you need an extension to reach a jack, be sure it is high quality. Instead, consider using a longer ethernet cable to reach the computer (or wireless).
- Modem overheating.
- Possible solution: Make sure the ventilation ports, usually located on the bottom of the modem are clear. Try mounting the modem on its side (vertically), on a hard surface or raised up on blocks so that air flow is optimal.
- Spider webs.
- Possible solution: Check that your telephone junction boxes are free of spider webs (they can conduct and short high frequency signals, says a local engineer who worked on early DSL-like hardware development).
- Wet weather, especially in the spring
- Possible solution: Often wet weather, especially during the spring melt, causes phone line performance to degrade (water gets in and temporarily changes the electrical characteristics of the line). Lines are supposed to be waterproof, but with age that can degrade. Such problems often 'dry up' as conditions improve.
Didn't work, now what?
Nothing works? Try:
- Searching the internet for ideas
- Posting to the NCF DSL discussion group
- If all those fail, try describing your problem to the NCF office via the Help page.