Head blueLogoText.gif NCF HelpWiki
Help | StartPage

Difference between revisions of "TP-Link TD-W9970 Configuration"

From Support
Jump to: navigation, search
 
m (See Also)
 
(117 intermediate revisions by 12 users not shown)
Line 1: Line 1:
[[File:td-9970-front.jpg|thumb|right|300px|The TP-Link TD-W9970 Modem Front]]
+
<div class="ncfrightbox w-25">{{Template:TP-Link TD-W9970}}</div>
[[File:td-9970_back.jpg|thumb|right|300px|The TP-Link TD-W9970 Modem Back]]
 
The TP-Link TD-W9970 is for use on service over 25 MB/s on networks using Bells' DSL infrastructure. NCF sells these modems for members on 25 MB and faster service.
 
  
This is the procedure NCF uses to configure a TP-Link TD-W9970 modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem manuals (DSL)|manual]].
+
[[File:TD-W9970_front.jpg|thumb|left|x250px|The TP-Link TD-W9970 Modem Front]]
 +
[[File:TD-W9970_back.jpg|thumb|left|x250px|The TP-Link TD-W9970 Modem Back]]
 +
The TP-Link TD-W9970 is for use on any service on networks using Bells' DSL infrastructure. To learn more about configuring your particular modem, consult the [[Modem Manuals#TP-Link Modems|manual]].
  
== Configure router for Dual Mode ADSL/VDSL operation==
+
=Routed=
Your router can support both ADSL mode and VDSL mode. If necessary, you could switch between ADSL plans and VDSL plans without having to buy a new router or even reconfigure your existing one.
+
 
 +
The TP-Link TD-W9970 modem router supports both ADSL and VDSL, and switches automatically to match the line it is connected to.  
 +
 
 +
==VDSL==
 +
{{Template:TD-W9970_Links}}
  
===Settings for VDSL===
 
 
We will start with the mode used for VDSL connections.  These include the following NCF DSL Plans:
 
We will start with the mode used for VDSL connections.  These include the following NCF DSL Plans:
* Freedom 15-10/300
+
* Freedom 10-7/Unl
* Freedom 25/300
+
* Freedom 15-10/Unl
* Freedom 50/300
+
* Freedom 25/Unl
 +
* Freedom 50/Unl
 +
 
 +
'''Quick Setup'''
  
=== Getting Started ===
+
'''NOTE:''' If the modem is brand new, "user name: admin" and "password: admin" will gain access.
NOTE: If the modem is brand new, "user name: admin and password admin" will gain access. If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the reset button with a paper clip for 6 to 9 seconds and then do step 1.
 
  
1. Once you access the modem browser at 192.168.1.1 and login (user name: admin and password admin), click the link high-lighted in red.
+
If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the '''Reset/Wi-Fi''' button for 6 to 9 seconds and then do step 1.
  
[[file:td-9970_1.jpg|Getting started]]
+
1. Once you access the modem from your [[browser]] at http://192.168.1.1 and login (user name: admin and password: admin), click the '''Quick Setup''' link in the Menu on the left.  
  
=== Advanced Setup ===
+
Then click '''Next''' on the '''Quick Setup-Start''' page.
2. Click on the "Advanced Setup" link on the LH side of the page.
 
[[file:td-9970_2.jpg|Advanced Setup]]
 
  
=== WAN Service ===
+
[[file:Td-w9970_setup1.png|721x721px|Getting started]]
3. Click on the "WAN Service" link under "Advanced Setup" and then click on the "Edit" link highlighted in red.
 
[[file:td-9970_3.jpg|WAN Service]]
 
  
=== Username Setup ===
+
'''Region and Time Zone'''
4. On the 'PPP Username and Password' page, fill  the username and password details in the field highlighted in red. Be sure to scroll  to the bottom of this page checking that "Enable Firewall", "Enable NAT" and "Enable SIP"  are all checked. Click "Next".
 
[[file:td-9970_4.jpg|960px|PPPOE set up]]
 
[[file:td-9970_505n_vdsl_NAT_SIP_005.png]]
 
  
=== PPPoE config save ===
+
{{Template:Back to the Top}}
<!--5. There will be two more pages to scroll through and them you can finally "Save" these changes. At this point, the Internet light on the TP-Link should turn from red and eventually to green.-->
 
  
Click on "ppp0.1" and then "Next"
+
# Set Region to '''Canada'''
[[File:td-9970_505n_adsl09.png|765px|none|Configuring ADSL2+ 9/11]]
+
# Time Zone to '''(GMT-05:00) Eastern Time (US & Canada)'''
 +
# Click '''Next'''
  
 +
[[file:Td-w9970_setup2.png|722x722px|Step2]]
  
 +
'''Auto Detection'''
  
Click on "ppp0.1" and then "Next"
+
{{Template:Back to the Top}}
[[File:td-9970_505n_adsl10.png|1000px|Configuring ADSL2+ 10/11]]
 
  
 +
# Click on '''No, I want to configure The Internet Connection myself'''
 +
# Click '''Next'''
  
 +
[[file:Td-w9970_setup3.png|724x724px|Step3]]
  
Click on "Apply/Save".
+
'''DSL'''
[[file:td-9970_5.jpg|PPoE config save]]
 
  
<!--=== Wireless Setup ===-->
+
{{Template:Back to the Top}}
<!--6. Click on the "Wireless" link on the RH side of the page.-->
 
<!--Change the SSID to the NCF standard name.-->
 
<!--Click on the "Security" subtab , store the NCF DSL password for the wi-fi password.-->
 
  
<!--===Modem Password Setup ===
+
# ISP: '''Other'''
7. Click on the "Management " link on the RH side of the page. Click on the "Access"?? subtab and then the "Passwords" sub.sub tab. Change the modem access password to NCF standard.
+
# L2 Interface Type: '''VDSL'''
 +
# Enable VLAN ID: '''checked'''
 +
# VLAN: '''35'''
 +
# Connection Type: '''PPPoE'''
 +
# Click '''Next'''
  
 +
[[file:Td-w9970_setup4.png|721x721px|Step4]]
  
I need some more images to complete this - all in due time.-->
+
'''PPPoE'''
  
 +
{{Template:Back to the Top}}
  
 +
# User name: '''ab123@ncf.ca''' (where ab123 is your NCF ID)
 +
# Password: '''••••••••''' (where •••••••• is your NCF DSL Password)
 +
# Confirm password: '''••••••••'''
 +
# Click '''Next'''
  
<!--[[File:td-9970_1.jpg|Configuring VDSL 1/5]]-->
+
[[file:Td-w9970_setup5.png|725x725px|Step5]]
<!--[[File:td-9970_2.jpg|Configuring VDSL 2/5]]-->
 
<!--[[File:td-9970_3.jpg|Configuring VDSL 3/5]]-->
 
<!--[[File:td-9970_4.jpg|Configuring VDSL 4/5]]-->
 
<!--[File:td-9970_5.jpg|Configuring VDSL 5/5]]-->
 
  
=== Add Settings for ADSL Mode===
+
'''3G/4G'''
Moving on now to add settings for ADSL mode.
+
 
ADSL plans include the following NCF DSL Plans:
+
{{Template:Back to the Top}}
 +
 
 +
# Click '''Next'''
 +
 
 +
[[file:Td-w9970_setup6.png|729x729px|Step6]]
 +
 
 +
'''Wireless'''
 +
 
 +
{{Template:Back to the Top}}
 +
 
 +
# Wireless: '''Enable'''
 +
# Wireless Network Name (SSID): '''NCF_XXXX''' (where XXXX are the last 4 digits of the modem serial number)
 +
# Channel: '''Auto'''
 +
# Mode: '''11n only'''
 +
# Security: '''WPA2'''
 +
# Password: '''DSL Password'''
 +
# Click '''Next'''
 +
 
 +
[[file:Td-w9970_setup7.png|705x705px|Step7]]
 +
 
 +
'''Confirm'''
 +
 
 +
{{Template:Back to the Top}}
 +
 
 +
# Verify all setting are as entered
 +
# Click '''Next'''
 +
 
 +
[[file:Td-w9970_setup8.png|711x711px|Step8]]
 +
 
 +
'''Complete'''
 +
 
 +
{{Template:Back to the Top}}
 +
 
 +
# Click '''Finish'''
 +
 
 +
'''Stay logged-in'''
 +
# Click '''Network''' (left-hand menu, 4th link from top)
 +
#Click '''WAN Settings'''
 +
 
 +
'''DSL WAN Interface'''
 +
# Click on '''Action: Edit''' (entry with pppoe_ptm_35_1_d, right-hand side of table)
 +
 
 +
'''WAN Settings'''
 +
 
 +
{{Template:Back to the Top}}
 +
 
 +
# WAN Service Setup, enter...
 +
# Enable IPv6: '''Selected'''
 +
# Click '''Advance'''
 +
# Enable SPI Firewall: '''selected'''
 +
# Enable IGMP Proxy: '''un-select'''
 +
# Click '''Save'''
 +
 
 +
== ADSL ==
 +
{{Template:TD-W9970_Links}}
 +
 
 +
Moving on now to add settings for ADSL. ADSL is required for the following NCF DSL Plans:
 
* Freedom 6/300
 
* Freedom 6/300
 
* Freedom 7/300
 
* Freedom 7/300
 
* Freedom 15-1/300
 
* Freedom 15-1/300
  
#Click on "Advanced Setup"
+
'''Stay logged-in'''
#Click on "Layer2 Interface"
+
# Click '''Network''' (left-hand menu, 4th link from top)
#Click on "ATM Interface"
+
# Click '''WAN Settings'''
#Click on "Add"
+
 
<!--[[File:td-9970_505n_adsl01.png|Configuring ADSL2+ 1/11]]-->
+
'''DSL WAN Interface'''
<!--[[File:td-9970_505n_adsl02.png|Configuring ADSL2+ 2/11]]-->
+
 
[[File:td-9970_505n_adsl03.png|1000px|Configuring ADSL2+ 3/11]]
+
{{Template:Back to the Top}}
 +
 
 +
# Click on '''Action: Delete''' (1st entry, right-hand side of table)
 +
# Then click '''Add''' button
 +
 
 +
[[file:Td-w9970_setup9.png|1195x1195px|Adding ADSL2+ WAN Config 1/2]]
  
#Under "Select DSL Latency", check both "Path0 (Fast)" and "Path1 (Interleaved)"
+
'''WAN Settings'''
#Ensure that VPI is 0 and that VCI is 35.
 
# For everything else, use the defaults.
 
#Scroll to the bottom of the page, and click "Next".
 
[[File:td-9970_505n_adsl04.png|1000px|Configuring ADSL2+ 4/11]]
 
  
# Click "Advanced Setup"
+
{{Template:Back to the Top}}
#Click "WAN Service"
 
#Click "Add"
 
[[File:td-9970_505n_adsl05.png|1000px|Configuring ADSL2+ 5/11]]
 
  
#From the drop-down box, select "atm0/(4_0_35)"
+
# DSL Modulation Type: '''ADSL'''
#Click "Next"
+
# ATM Configuration: '''VPI/VCI = 0/35'''
[[File:td-9970_505n_adsl06.png|1000px|Configuring ADSL2+ 6/11]]
+
# WAN Service Setup
 +
## Connection Type: '''PPPoE'''
 +
## PPP Username: '''ab123@ncf.ca''' (where ab123 is your NCF ID)
 +
## PPP Password: '''••••••••''' (your NCF DSL Password)
 +
## Confirm password: '''••••••••'''
 +
## Enable IPv4: '''selected'''
 +
## Enable IPv6: '''select'''
 +
# Click '''Advance'''
 +
## Enable SPI Firewall: '''selected'''
 +
## Enable IGMP Proxy: '''un-select'''
 +
# Click '''Save'''
  
#Ensure "PPPoE" is the active choice.
+
[[file:Td-w9970_setup10.png|804x804px|Adding ADSL2+ WAN Config 2/2]]
#Ensure "Service description" is as shown.
 
#Click "Next".
 
[[File:td-9970_505n_adsl07.png|1000px|Configuring ADSL2+ 7/11]]
 
  
Ensure "Enable Firewall", "Enable NAT" and "Enable SIP" are checked. Scroll to the bottom of the page and click "Next".
+
== DNS Fix ==
[[File:td-9970_505n_adsl08.png|1000px|Configuring ADSL2+ 8/11]]
+
{{Template:TD-W9970_Links}}
  
Click on "ppp0.1" and then "Next"
+
There is a known issue where the internal DNS server sometimes stop responding after swapping between ADSL and VDSL connections. To avoid this issue, we recommend hard-coding a public DNS server instead of using the internal one.
[[File:td-9970_505n_adsl09.png|1000px|Configuring ADSL2+ 9/11]]
 
  
Click on "ppp0.1" and then "Next"
+
'''DHCP Settings'''
[[File:td-9970_505n_adsl10.png|1000px|Configuring ADSL2+ 10/11]]
+
# DNS Server: '''1.1.1.1'''
 +
# Secondary DNS Server: '''1.0.0.1'''
  
Click on "Apply/Save"
+
[[file:02-dsn-fix.png|720x720px|DNS Fix for TD-W9970]]
[[File:td-9970_505n_adsl11.png|1000px|Configuring ADSL2+ 11/11]]
 
  
'''You are done adding the ADSL settings. Now, skip ahead to [[#Wireless_Configuration|Wireless Configuration]].'''
+
== UPnP ==
 +
{{Template:TD-W9970_Links}}
 +
 
 +
# Click on '''Forwarding''' (left-hand menu, near the middle)
 +
# UPnP: '''de-select'''
 +
[[File:TD-W9970_setup13.png|frameless|732x732px]]
 +
 
 +
== Time ==
 +
{{Template:TD-W9970_Links}}
 +
 
 +
# Click on '''System Tools''' (left-hand menu, towards the bottom)
 +
# Select '''Time Settings'''
 +
# Time Zone: '''(GMT-05:00) Eastern Time (US & Canada)'''
 +
# NTP Server 1: '''time.nrc.ca'''
 +
# Enable DST: '''checked'''
 +
# Modify DST Start: '''2nd Sunday in March'''
 +
# Modify DST End: '''1st Sunday in November'''
 +
# Click '''Save'''
 +
 
 +
[[file:Td-w9970_setup12.png|734x734px|Configuring Time Settings]]
 +
 
 +
== Manage Control==
 +
{{Template:TD-W9970_Links}}
 +
 
 +
# Click on '''System Tools''' (left-hand menu, towards the bottom)
 +
# Select '''Manage Control'''
 +
# For the user '''admin''' we use the member's '''DSL Password''' – user name & password should not exceed 15 characters
 +
# Enter it once and again below to confirm
 +
# Ensure ICMP (Ping) is set to '''Local only''' (default setting)
 +
#Click '''Save'''
 +
 
 +
[[File:Td-w9970_setup11.png|frameless|713x713px]]
 +
 
 +
== CWMP ==
 +
{{Template:TD-W9970_Links}}
 +
 
 +
# Click on '''System Tools''' (left-hand menu, towards the bottom)
 +
# Select '''CWMP Settings'''
 +
# Ensure that CWMP is '''de-selected''' (default setting)
 +
# Ensure that Inform is '''de-selected''' (default setting)
 +
# Click '''Save'''
 +
 
 +
==Firewall==
 +
{{Template:TD-W9970_Links}}
 +
 
 +
# Click '''Firewall''' in the left column
 +
# Select '''Enable Firewall''' if it's not '''Enabled'''
 +
 
 +
=Bridge=
 +
{{Template:TD-W9970_Links}}
  
== Configure as bridge ==
 
 
Do this only if you prefer to use your own external router rather than the one built into your TP-Link unit.
 
Do this only if you prefer to use your own external router rather than the one built into your TP-Link unit.
  
 
# Connect power and turn on the modem with the button on the back.
 
# Connect power and turn on the modem with the button on the back.
 
# Connect an Ethernet LAN cable to one of the yellow rear ports
 
# Connect an Ethernet LAN cable to one of the yellow rear ports
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
+
# In the browser's address bar, enter the IP address for the modem interface page: [http://192.168.1.1 192.168.1.1]
 
# If the modem is fresh from the factory, use the default user name and password to gain access
 
# If the modem is fresh from the factory, use the default user name and password to gain access
 
##'''user:''' admin  
 
##'''user:''' admin  
 
##'''password:''' admin
 
##'''password:''' admin
  
If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.
+
If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, press the reset/Wi-Fi button on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.
 +
 
 +
==VDSL==
 +
{{Template:TD-W9970_Links}}
 +
 
 +
# Click on '''Quick Setup'''.
 +
 
 +
'''DSL'''
 +
{{Template:Back to the Top}}
 +
 
 +
# ISP: '''Other'''
 +
# L2 Interface Type: '''VDSL'''
 +
# Enable VLAN ID: '''checked'''
 +
# VLAN: '''35'''
 +
# Connection Type: '''Bridge'''
 +
# Click '''Next'''
 +
 
 +
[[File:Td-w9970_bridge1.png|692x692px|Configuring for Bridge Mode 1/4]]
 +
 
 +
'''Wireless'''
 +
{{Template:Back to the Top}}
 +
 
 +
# Wireless: '''Disable'''
 +
# Click '''Next'''
  
# Click on Advanced Setup and WAN Service and click on Add
+
[[File:Td-w9970_bridge4.png|689x689px|Configuring for Bridge Mode 4/4]]
# The defaults are fine; click on Next.
 
# Click on Bridging and ensure the 802.1P and 802.1Q are set to 0 and 35, then click on Next.
 
# Click on Apply/Save
 
# Done!
 
  
See screenshots below:
+
'''Confirm'''
 +
{{Template:Back to the Top}}
  
[[File:td-9970_505n_bridge_1.png|Configuring for Bridge Mode 1/5]]
+
# Verify all setting are as entered
[[File:td-9970_505n_bridge_2.png|Configuring for Bridge Mode 2/5]]
+
# Click '''Next'''
[[File:td-9970_505n_bridge_3.png|Configuring for Bridge Mode 3/5]]
 
[[File:td-9970_505n_bridge_4.png|Configuring for Bridge Mode 4/5]]
 
[[File:td-9970_505n_bridge_5.png|Configuring for Bridge Mode 5/5]]
 
  
== Wireless Configuration ==
+
[[File:Td-w9970_bridge2.png|687x687px|Configuring for Bridge Mode 2/4]]
Continuing now to set the '''Wireless''' configuration
 
# Ensure '''Enable Wireless''' is checked
 
# The '''SSID''' is set to NCF plus a random number, such as '''NCF_123456'''. It is recommended you not use your first or last name, or street address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
 
# Click on '''Apply/Save''' at the bottom.
 
[[File:td-9970_505n_adsl12.png|1000px|Configuring Wireless 1/2]]
 
  
 +
'''Stay logged-in'''
 +
# Click '''Network''' (left-hand menu, 4th link from top)
 +
# Click '''WAN Settings'''
 +
# On the '''DSL WAN Interface''' page click '''Add'''
  
# Click on '''Security''' on the left.
+
==ADSL==
# Set the '''Network Authentication''' to Mixed WPA2/WPA-PSK
+
{{Template:TD-W9970_Links}}
# Uncheck '''Use base MAC address as WPA/WAPI passphrase
 
# Set the '''WPA/WAPI passphrase''' to be your DSL-Password
 
# Click '''Apply/save'''.
 
[[File:td-9970_505n_adsl13.png|1000px|Configuring Wireless 2/2]]
 
  
== Password protect the Admin Role ==
+
'''WAN Settings'''
# Click on '''Management''' on the left.  Below it other options appear.
+
# DSL Modulation Type: select '''ADSL'''
# Select '''Access Control'''  
+
# ATM Configuration, enter...
# Select '''Passwords'''  
+
#* VPI: '''0'''
# Enter '''admin''' for the User Name
+
#* VCI: '''35'''
# Enter '''admin''' for the Old Password
+
# WAN Service Setup, enter...
# For the New Password use your DSL-Password or another strong password.
+
#* Connection Type: '''Bridge'''
# Enter it once and again below to confirm
+
# Click '''Save'''
# Save the changes with '''Apply/Save'''
 
  
Click on "Device Info". A pop-up log-in screen appears, and asks for sign-in. Use the User-ID '''admin''' and the DSL-Password just set. Return to the same configure page you were just at.
+
[[File:Td-w9970_bridge3.png|699x699px|Configuring for Bridge Mode 3/3]]
  
 +
Follow the instructions in [[#Manage Control|Manage Control]] to secure your modem.
  
[[File:td-9970_505n_adsl14.png|1000px|Setting Admin Password]]
+
= See Also =
 +
{{Template:TD-W9970_Links}}
  
== See also ==
+
*[[Modem Configuration]] - for a complete list of instructions for all NCF modems
*[http://www.ncf.ca/ncf/dsl/modem/TP-Link_3xx-5xx_Gateway_User_Manual.pdf TP-Link TD-W9970 modem manual]
+
*[[Modem Lights#TP-Link|About TP-Link Modem Lights]]
*[https://www.ncf.ca/ncf/support/w/images/f/f8/Modem_Info_Pages_-_TP-Link_505n_v1.0.pdf NCF TP-Link TD-W9970 modem instruction sheet]
+
*[http://www.ncf.ca/ncf/dsl/modem/TD-W9970_V1_UG.pdf TP-Link TD-W9970 manual]
*[[About DSL modem lights - TP-Link modems]]
+
*[https://www.ncf.ca/ncf/support/w/images/8/8c/About_Your_TP-Link_TD-W9970.pdf About Your TP-Link TD-W9970]
 +
*[[Changing WiFi Channels on TP-Link TD-W9970]]
 
*[[Dynamic DNS]]
 
*[[Dynamic DNS]]
*[[Modem Configuration (DSL)]] - for a complete list of instructions for all NCF modems
+
*[[Modem Manuals]]
 
*[[Port forwarding]]
 
*[[Port forwarding]]
[[Category: DSL]]
+
 
 +
[[Category:DSL]]
 +
[[Category:Modems]]

Latest revision as of 15:22, 10 April 2019

The TP-Link TD-W9970 Modem Front
The TP-Link TD-W9970 Modem Back

The TP-Link TD-W9970 is for use on any service on networks using Bells' DSL infrastructure. To learn more about configuring your particular modem, consult the manual.

Routed

The TP-Link TD-W9970 modem router supports both ADSL and VDSL, and switches automatically to match the line it is connected to.

VDSL

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also

We will start with the mode used for VDSL connections. These include the following NCF DSL Plans:

  • Freedom 10-7/Unl
  • Freedom 15-10/Unl
  • Freedom 25/Unl
  • Freedom 50/Unl

Quick Setup

NOTE: If the modem is brand new, "user name: admin" and "password: admin" will gain access.

If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the Reset/Wi-Fi button for 6 to 9 seconds and then do step 1.

1. Once you access the modem from your browser at http://192.168.1.1 and login (user name: admin and password: admin), click the Quick Setup link in the Menu on the left.

Then click Next on the Quick Setup-Start page.

Getting started

Region and Time Zone

  1. Set Region to Canada
  2. Time Zone to (GMT-05:00) Eastern Time (US & Canada)
  3. Click Next

Step2

Auto Detection

  1. Click on No, I want to configure The Internet Connection myself
  2. Click Next

Step3

DSL

  1. ISP: Other
  2. L2 Interface Type: VDSL
  3. Enable VLAN ID: checked
  4. VLAN: 35
  5. Connection Type: PPPoE
  6. Click Next

Step4

PPPoE

  1. User name: ab123@ncf.ca (where ab123 is your NCF ID)
  2. Password: •••••••• (where •••••••• is your NCF DSL Password)
  3. Confirm password: ••••••••
  4. Click Next

Step5

3G/4G

  1. Click Next

Step6

Wireless

  1. Wireless: Enable
  2. Wireless Network Name (SSID): NCF_XXXX (where XXXX are the last 4 digits of the modem serial number)
  3. Channel: Auto
  4. Mode: 11n only
  5. Security: WPA2
  6. Password: DSL Password
  7. Click Next

Step7

Confirm

  1. Verify all setting are as entered
  2. Click Next

Step8

Complete

  1. Click Finish

Stay logged-in

  1. Click Network (left-hand menu, 4th link from top)
  2. Click WAN Settings

DSL WAN Interface

  1. Click on Action: Edit (entry with pppoe_ptm_35_1_d, right-hand side of table)

WAN Settings

  1. WAN Service Setup, enter...
  2. Enable IPv6: Selected
  3. Click Advance
  4. Enable SPI Firewall: selected
  5. Enable IGMP Proxy: un-select
  6. Click Save

ADSL

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also

Moving on now to add settings for ADSL. ADSL is required for the following NCF DSL Plans:

  • Freedom 6/300
  • Freedom 7/300
  • Freedom 15-1/300

Stay logged-in

  1. Click Network (left-hand menu, 4th link from top)
  2. Click WAN Settings

DSL WAN Interface

  1. Click on Action: Delete (1st entry, right-hand side of table)
  2. Then click Add button

Adding ADSL2+ WAN Config 1/2

WAN Settings

  1. DSL Modulation Type: ADSL
  2. ATM Configuration: VPI/VCI = 0/35
  3. WAN Service Setup
    1. Connection Type: PPPoE
    2. PPP Username: ab123@ncf.ca (where ab123 is your NCF ID)
    3. PPP Password: •••••••• (your NCF DSL Password)
    4. Confirm password: ••••••••
    5. Enable IPv4: selected
    6. Enable IPv6: select
  4. Click Advance
    1. Enable SPI Firewall: selected
    2. Enable IGMP Proxy: un-select
  5. Click Save

Adding ADSL2+ WAN Config 2/2

DNS Fix

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also

There is a known issue where the internal DNS server sometimes stop responding after swapping between ADSL and VDSL connections. To avoid this issue, we recommend hard-coding a public DNS server instead of using the internal one.

DHCP Settings

  1. DNS Server: 1.1.1.1
  2. Secondary DNS Server: 1.0.0.1

DNS Fix for TD-W9970

UPnP

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also
  1. Click on Forwarding (left-hand menu, near the middle)
  2. UPnP: de-select

TD-W9970 setup13.png

Time

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also
  1. Click on System Tools (left-hand menu, towards the bottom)
  2. Select Time Settings
  3. Time Zone: (GMT-05:00) Eastern Time (US & Canada)
  4. NTP Server 1: time.nrc.ca
  5. Enable DST: checked
  6. Modify DST Start: 2nd Sunday in March
  7. Modify DST End: 1st Sunday in November
  8. Click Save

Configuring Time Settings

Manage Control

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also
  1. Click on System Tools (left-hand menu, towards the bottom)
  2. Select Manage Control
  3. For the user admin we use the member's DSL Password – user name & password should not exceed 15 characters
  4. Enter it once and again below to confirm
  5. Ensure ICMP (Ping) is set to Local only (default setting)
  6. Click Save

Td-w9970 setup11.png

CWMP

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also
  1. Click on System Tools (left-hand menu, towards the bottom)
  2. Select CWMP Settings
  3. Ensure that CWMP is de-selected (default setting)
  4. Ensure that Inform is de-selected (default setting)
  5. Click Save

Firewall

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also
  1. Click Firewall in the left column
  2. Select Enable Firewall if it's not Enabled

Bridge

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also

Do this only if you prefer to use your own external router rather than the one built into your TP-Link unit.

  1. Connect power and turn on the modem with the button on the back.
  2. Connect an Ethernet LAN cable to one of the yellow rear ports
  3. In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
  4. If the modem is fresh from the factory, use the default user name and password to gain access
    1. user: admin
    2. password: admin

If the modem was previously configured for someone, the password would be the previous user's DSL password. If it is unknown then do a reset to factory default, press the reset/Wi-Fi button on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.

VDSL

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also
  1. Click on Quick Setup.

DSL

  1. ISP: Other
  2. L2 Interface Type: VDSL
  3. Enable VLAN ID: checked
  4. VLAN: 35
  5. Connection Type: Bridge
  6. Click Next

Configuring for Bridge Mode 1/4

Wireless

  1. Wireless: Disable
  2. Click Next

Configuring for Bridge Mode 4/4

Confirm

  1. Verify all setting are as entered
  2. Click Next

Configuring for Bridge Mode 2/4

Stay logged-in

  1. Click Network (left-hand menu, 4th link from top)
  2. Click WAN Settings
  3. On the DSL WAN Interface page click Add

ADSL

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also

WAN Settings

  1. DSL Modulation Type: select ADSL
  2. ATM Configuration, enter...
    • VPI: 0
    • VCI: 35
  3. WAN Service Setup, enter...
    • Connection Type: Bridge
  4. Click Save

Configuring for Bridge Mode 3/3

Follow the instructions in Manage Control to secure your modem.

See Also

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | FirewallBridge | VDSL | ADSLSee Also