Head blueLogoText.gif NCF HelpWiki
Help | StartPage

Difference between revisions of "TP-Link TD-W8951ND Configuration"

From Support
Jump to navigation Jump to search
(4 intermediate revisions by 2 users not shown)
Line 1: Line 1:
[[File:TP-Link TD-W8951ND.jpg|thumb|right|300px|The TP-Link 8951ND modem]]
<div class="ncfrightbox"> {{Template:Modem Links}} </div>
This is the procedure NCF uses to configure a TP-Link 8951ND modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem manuals (DSL)|manual]].
[[File:TP-Link TD-W8951ND.jpg|thumb|left|x250px|The TP-Link 8951ND modem]]
This is the procedure NCF uses to configure a TP-Link 8951ND modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem Manuals|manual]].


=== Configure as router ===
= Configure as Router=


# Connect power and turn on the modem with the black button on the back.
# Connect power and turn on the modem with the black button on the back.
Line 12: Line 13:


If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 15 seconds to reset. The user name and password will now be as above.
If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 15 seconds to reset. The user name and password will now be as above.
{{:Template:Quick Facts (TP-Link DSL modem)}}


# When presented with the TP-Link configuration page, select the '''Quick Start''' option at the top left.
# When presented with the TP-Link configuration page, select the '''Quick Start''' option at the top left.
Line 26: Line 28:
# Click '''Next'''
# Click '''Next'''


{{:Template:Quick Facts (TP-Link DSL modem)}}
Continuing now to set the '''user name''' and '''password'''
Continuing now to set the '''user name''' and '''password'''
# PPPoE Service name can remain blank
# PPPoE Service name can remain blank
Line 47: Line 48:
Proceed with four more steps - Setting administrator access, and wireless locale setting
Proceed with four more steps - Setting administrator access, and wireless locale setting


=== VoIP Enabling ===
== VoIP Enabling==
# Launch Telnet session from the computer command line.
# Launch Telnet session from the computer command line.
# Enter the following commands:
# Enter the following commands:
Line 55: Line 56:
## x (press x)
## x (press x)


=== Password protect the Admin Role ===  
==Password protect the Admin Role==
# Click on '''Maintenance''' in the menu along the top of the page.  Below it other options appear.
# Click on '''Maintenance''' in the menu along the top of the page.  Below it other options appear.
# Select '''Administration'''  
# Select '''Administration'''  
Line 64: Line 65:
A pop-up log-in screen appears, and asks for sign-in. Use the User-ID '''admin''' and the DSL-Password just set. Return to the same configure page you were just at.
A pop-up log-in screen appears, and asks for sign-in. Use the User-ID '''admin''' and the DSL-Password just set. Return to the same configure page you were just at.


===Set daylight savings time===
==Set daylight savings time==
# In '''Maintenance''' select '''Time Zone'''.
# In '''Maintenance''' select '''Time Zone'''.
# Daylight Saving: Enabled
# Daylight Saving: Enabled


===Turn on SPI firewalling===
==Turn on SPI firewalling==
# In '''Advanced Setup''' select '''Firewall'''.
# In '''Advanced Setup''' select '''Firewall'''.
# SPI: Enabled
# SPI: Enabled


=== Final area setting and check ===
==Final area setting and check==
# Click '''Interface Setup''' in the top-of-page menu
# Click '''Interface Setup''' in the top-of-page menu
# Now select '''Wireless''' in the menu below that.
# Now select '''Wireless''' in the menu below that.
Line 88: Line 89:
The modem should now synchronize and connect to your DSL service if the service is operating. You may need to reboot the modem to get it to connect.
The modem should now synchronize and connect to your DSL service if the service is operating. You may need to reboot the modem to get it to connect.


==Security==
=Security=
In January 2014 it was revealed that some models of TP-Link modem, including this model, are subject to hacking if they are running out dated firmware and if the remote access (ACL) is set to allow remote access. [[CERT-announced vulnerability of TP-Link modem/router|This web page]] provides more detailed information on the vulnerability. Latest firmware versions can be checked on the [https://www.tp-link.com/ca/download/TD-W8951ND.html TP-Link website].
In January 2014 it was revealed that some models of TP-Link modem, including this model, are subject to hacking if they are running out dated firmware and if the remote access (ACL) is set to allow remote access. [[CERT-announced vulnerability of TP-Link modem/router|This web page]] provides more detailed information on the vulnerability. Latest firmware versions can be checked on the [https://www.tp-link.com/ca/download/TD-W8951ND.html TP-Link website].


===ACL===
==ACL==
#To be sure your modem is secure, click on "Access Management". By default the "ACL" tab will be active.
#To be sure your modem is secure, click on "Access Management". By default the "ACL" tab will be active.
#Ensure your ACL page looks like the screen shot below. If not, choose "WAN" from the "Interface" drop-down box.
#Ensure your ACL page looks like the screen shot below. If not, choose "WAN" from the "Interface" drop-down box.
Line 98: Line 99:
[[File:TP-Link modem with ACL deactivated.jpg|TP-Link modem with ACL deactivated]]
[[File:TP-Link modem with ACL deactivated.jpg|TP-Link modem with ACL deactivated]]


==See also==
=See also=
*[https://www.ncf.ca/ncf/support/w/images/9/91/Modem_Info_Pages_-_8951_v1.2.pdf NCF TP-Link 8951ND Instruction sheet]
*[https://www.ncf.ca/ncf/support/w/images/9/91/Modem_Info_Pages_-_8951_v1.2.pdf NCF TP-Link TD-W8951ND Instruction sheet]
*[[:File:CHANGING THE WIRELESS CHANNEL ON TP-LINK TD-8951ND.pdf|Changing Wireless Channels on TP-Link TD-W8951ND]]  
*[[CERT-announced vulnerability of TP-Link modem/router]]
*[[CERT-announced vulnerability of TP-Link modem/router]]
*[[Dynamic DNS]]
*[[Dynamic DNS]]

Revision as of 16:07, 12 November 2018

The TP-Link 8951ND modem

This is the procedure NCF uses to configure a TP-Link 8951ND modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the manual.

Configure as Router

  1. Connect power and turn on the modem with the black button on the back.
  2. Connect an Ethernet LAN cable to one of the yellow rear ports
  3. In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
  4. If the modem is fresh from the factory, use the default user name and password to gain access
    1. user: admin
    2. password: admin

If the modem was previously configured for someone, the password would be the previous user's DSL password. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 15 seconds to reset. The user name and password will now be as above.

DSL Quick Configuration Info

(TP-Link DSL modems)

Modem Web Interface http://192.168.1.1
Modem login Username: admin

Password: (see 'password' below)

VPI / VCI (ADSL) 0.35
VLAN (VDSL) 35
Protocol PPPoE
DSL username (eg. aa999@ncf.ca)
DSL Password Starts with 'ncf' (not the same

as your NCF Start Page login)

Firewall Enabled by default (recommended)
Wireless If enabled, WPA-PSK (WPA2)
  1. When presented with the TP-Link configuration page, select the Quick Start option at the top left.
  2. Select Run Wizard to proceed.

Now a window pops open and you can begin to set up the details of the interface.

  1. Select Next to proceed
  2. Set the Time Zone Eastern
  3. Click Next
  4. Set the connection type of PPPoE/PPPoA
  5. Click Next
  6. Ensure VPI is set to 0 and VCI is set to 35
  7. Click Next
  8. Verify that PPPoverEthernet PPPoE is selected
  9. Click Next

Continuing now to set the user name and password

  1. PPPoE Service name can remain blank
  2. PPP username in the form ab123@ncf.ca (NOTE the "@ncf.ca" part! - it will not work without that!)
  3. PPP Password uses DSL Password (This is not your NCF account password, but your DSL password and was provided to you when you signed up for service, it starts with "ncf...")
  4. Ensure that the encapsulation remains at PPPoE LLC (default)
  5. Click Next

Continuing now to set the wireless configuration

  1. Ensure Access Point indicates activated
  2. The SSID is set to NCF plus a random number, such as NCF_123456. It is recommended you not use your first or last name, or street address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
  3. Broadcast SSID remains selected
  4. Auth Type - must be set to WPA2-PSK

...wait a moment for it to offer additional field for encryption and password...

  1. Set Encryption Type to be AES
  2. Set the Preshared Key to be your DSL-Password
  3. Click Next to Finish the wizard.

Proceed with four more steps - Setting administrator access, and wireless locale setting

VoIP Enabling

  1. Launch Telnet session from the computer command line.
  2. Enter the following commands:
    1. sys edit autoexec.net (press enter)
    2. i (when you press i, it means inserting the following commands to the system)
    3. ip nat service sip sw off (press enter)
    4. x (press x)

Password protect the Admin Role

  1. Click on Maintenance in the menu along the top of the page. Below it other options appear.
  2. Select Administration
  3. For the admin user use your DSL-Password or another strong password.
  4. Enter it once and again below to confirm
  5. Save the changes with Save

A pop-up log-in screen appears, and asks for sign-in. Use the User-ID admin and the DSL-Password just set. Return to the same configure page you were just at.

Set daylight savings time

  1. In Maintenance select Time Zone.
  2. Daylight Saving: Enabled

Turn on SPI firewalling

  1. In Advanced Setup select Firewall.
  2. SPI: Enabled

Final area setting and check

  1. Click Interface Setup in the top-of-page menu
  2. Now select Wireless in the menu below that.
  3. Choose Canada for the Channel Setup
  4. Click SAVE

Still on this page, Verify:

  1. The SSID in the form NCF_XXXXX or as you set.
  2. The Auth Type is WPA2-PSK
  3. The Encryption Type is AES and key is DSL-Password
  4. Click on the Internet tab
  5. Ensure that PVC2 has VPI/VCI set at 0/35
  6. Ensure that PPPoE credentials are set properly for your user name and password.

The modem should now synchronize and connect to your DSL service if the service is operating. You may need to reboot the modem to get it to connect.

Security

In January 2014 it was revealed that some models of TP-Link modem, including this model, are subject to hacking if they are running out dated firmware and if the remote access (ACL) is set to allow remote access. This web page provides more detailed information on the vulnerability. Latest firmware versions can be checked on the TP-Link website.

ACL

  1. To be sure your modem is secure, click on "Access Management". By default the "ACL" tab will be active.
  2. Ensure your ACL page looks like the screen shot below. If not, choose "WAN" from the "Interface" drop-down box.
  3. Select "deactivated".
  4. Click "Save".

TP-Link modem with ACL deactivated

See also