Head blueLogoText.gif NCF HelpWiki
Help | StartPage

Difference between revisions of "SpeedTouch 516 and 585 on ADSL2+"

From Support
Jump to navigation Jump to search
(copy edit)
(clarify)
Line 1: Line 1:
In 2009 Bell's infrastructure did not support ADSL2+, while the modems NCF sold then, the Thompson SpeedTouch 516 and 585s, did. Because the modems defaulted to ADSL2+ and not the ADSL1 then in use on Bell's networks the modems would not connect. To fix this problem a number of modems shipped at that time were configured to force them into ADSL1 mode, which solved the problem. Now that Bell's infrastructure requires ADSL2+ for 15 MB/s service these modems that were configured that way will not work with 15 MB/s service unless reconfigured.
In 2009 Bell's infrastructure did not support ADSL2+, while the modems NCF sold then, the Thompson SpeedTouch 516 and 585s, did. Because the modems defaulted to ADSL2+ and not the ADSL1 then in use on Bell's networks the modems would not connect. To fix this problem a number of modems shipped at that time were configured by NCF to force them into ADSL1 mode, which solved the problem. Now that Bell's infrastructure requires ADSL2+ for 15 MB/s service these modems that were configured that way will not work with 15 MB/s service unless reconfigured.


The configuration cannot be fixed by doing a factory reset, instead it must be done by [https://en.wikipedia.org/wiki/Telnet Telnet] into the modem and changing it via command line. Fortunately this is easy to do.
The configuration cannot be fixed by doing a factory reset, instead it must be done by [https://en.wikipedia.org/wiki/Telnet Telnet] into the modem and changing it via command line. Fortunately this is easy to do.

Revision as of 19:28, 1 May 2013

In 2009 Bell's infrastructure did not support ADSL2+, while the modems NCF sold then, the Thompson SpeedTouch 516 and 585s, did. Because the modems defaulted to ADSL2+ and not the ADSL1 then in use on Bell's networks the modems would not connect. To fix this problem a number of modems shipped at that time were configured by NCF to force them into ADSL1 mode, which solved the problem. Now that Bell's infrastructure requires ADSL2+ for 15 MB/s service these modems that were configured that way will not work with 15 MB/s service unless reconfigured.

The configuration cannot be fixed by doing a factory reset, instead it must be done by Telnet into the modem and changing it via command line. Fortunately this is easy to do.

Accessing Telnet

Linux and Mac

On Linux operating systems you can access telnet by opening a terminal and typing in "telnet 192.168.1.1" at the prompt.

Windows

On Windows XP and Vista operating systems telnet can be accessed by opening "run" and the "cmd" command and entering telnet.

In Windows 7 and 8 you can bring up the command line by entering "cmd" in the search bar.

In any version of Windows you can also run telnet by installing and using the PuTTY free software application.

Configuring the modem for ADSL2+

The commands are:

telnet 192.168.1.254 User: admin/Administrator Pass: <your dsl password>

xdsl debug multimode config=t1.413issue2+g992.1_annex_a+g992.3_annex_a+g992.3_annex_l+g992.3_annex_m+g992.5_annex_a+g992.5_annex_m

saveall

That "xdsl..." is a single command, so in copy and pasting be careful to copy the entire line without any carriage returns, which would compromise the command.

Thompson dsl2 fix.png

External links