Head blueLogoText.gif NCF HelpWiki
Help | StartPage

Difference between revisions of "SmartRG SR505N Configuration"

From Support
Jump to navigation Jump to search
 
(76 intermediate revisions by 5 users not shown)
Line 1: Line 1:
<div class="ncfrightbox w-25"> {{Template:SmartRG SR505n}} </div>
<div class="ncfrightbox w-25"> {{Template:SmartRG SR505n}} </div>
=Preparation=
=Preparation=
Updated: 2018-08-20
Updated: 2020-09-08
Recommended Firmware Version: 2.5.0.14
 
'''Recommended Firmware Version: 2.6.2.6. Please see the Firmware section below for more details.'''
 
The SmartRG SR505n modem router supports both ADSL mode and VDSL mode. Provided it is configured correctly, it can be switched between ADSL and VDSL plans without the owner having to buy a new modem or even re-configure your existing one.
* Note: Fees for changing plans may still apply. Consult: [[DSL Rates]]


Before you start configuring the SmartRG SR505n, there are 4 things to check:
Before you start configuring the SmartRG SR505n, there are 4 things to check:
Line 8: Line 12:
# '''Factory Settings and Standard Configuration:''' These instructions assume you're configuring SmartRG SR505n modem out of the box or after a factory reset.  If the modem is not new, it is recommended to reset the modem to the factory defaults '''by holding down the reset button with a paper clip for ~10 seconds.'''  
# '''Factory Settings and Standard Configuration:''' These instructions assume you're configuring SmartRG SR505n modem out of the box or after a factory reset.  If the modem is not new, it is recommended to reset the modem to the factory defaults '''by holding down the reset button with a paper clip for ~10 seconds.'''  
#* Also, these settings are our recommendations for most NCF members. To learn more about making custom changes to your particular modem, consult the [[Modem Manuals|manual]].
#* Also, these settings are our recommendations for most NCF members. To learn more about making custom changes to your particular modem, consult the [[Modem Manuals|manual]].
#'''Modem Installation - Configure over Ethernet:''' Consult the [https://www.ncf.ca/ncf/support/w/images/f/f8/Modem_Info_Pages_-_SmartRG_505n_v1.0.pdf SmartRG SR505N modem instruction sheet] (page 1) on how to set up the modem and connect to it over ethernet. ''We do not recommend configuring your modem over a WiFi connection.''
#'''Modem Installation - Configure over Ethernet:''' Consult the [https://www.ncf.ca/ncf/support/w/images/f/f8/Modem_Info_Pages_-_SmartRG_505n_v1.0.pdf SmartRG SR505N modem instruction sheet] (page 1) on how to set up the modem and connect to it over ethernet. ''We do not recommend configuring your modem over a Wi-Fi connection.''
#'''Configurations Methods:''' The 2 main ways of configuring the SmartRG SR505n modem:
#'''Configurations Methods:''' The 2 main ways of configuring the SmartRG SR505n modem:
#* Using a custom configuration File: Request a custom configuration file for your NCF DSL from [mailto:support@ncf.ca support@ncf.ca].
#* Using a custom configuration File: You can request an NCF custom configuration file for your NCF DSL connection from [mailto:support@ncf.ca support@ncf.ca] (available to NCF members only)
#* Manually following configuration steps
#* Manually following configuration steps.
# '''Configuration Options:'''
# '''Configuration Options:'''
#* [[#Configure for Routed Operation with WiFi|Routed Operation with WiFi]] - Standard configuration for most members with SmartRG SR505n serving as both modem and WiFi router.
#* [[#Configure for Routed Operation with WiFi|Routed Operation with WiFi]] - Standard configuration for most members with SmartRG SR505n serving as both modem and Wi-Fi router
#* Routed Operation with separate WiFi Router - Recommended configuration for members with their own WiFi router. The modem will make the PPPoE authentication and both devices will negotiate DHCP.
#* [[#Configure_for_Routed_Operation_with_separate_WiFi_Router|Routed Operation with separate WiFi Router]] - Recommended configuration for members with their own Wi-Fi router. The modem will make the PPPoE authentication and both devices will negotiate DHCP
#* Bridged Operation with separate WiFi Router - '''(Advanced)''' for members with their own routers and are knowledgeable about managing it themselves. The router with handle both authentication  and DHCP.
#* [[#Bridge Operation|Bridged Operation with separate WiFi Router]] - '''(Advanced)''' for members with their own routers and are knowledgeable about managing it themselves. The router with handle both authentication  and DHCP.
 
=Using Custom Configuration File=
{{Template:Back_to_the_Top}}
Your SmartRG modem can be configured for Routed or Bridged Operation by a custom configuration file. The custom configuration will include parameters specific to your NCF account.
 
1. Request a custom configuration file from [Mailto:support@ncf.ca support@ncf.ca] and save it at a location you will remember.
== Log into Modem Web Interface ==
{{Template:Back_to_the_Top}}
2. Enter http://192.168.1.1 info the address bar at in your web browser. Click on '''Manage Gateway (advanced)''' and login with username: '''admin''' and password: '''admin''' (if your modem has been properly reset. If not try your '''NCF DSL password''').
[[File:SR505n-Login Page.png|alt=SmartRG SR505n Login Page|none|thumb|540x540px|SmartRG SR505n Login Page]]
 
== Uploading the File ==
{{Template:Back_to_the_Top}}
3. Go to the '''Management''' Menu link, and then click on the '''Settings''' sub-menu link and then on the '''Update'''.
* Click on the '''Browse''' link (in the Update Running Broadband Router Settings section) and navigate to the custom configuration file you saved.
* Click on '''Update Running Settings'''.
[[File:SR505n-Settings-Update.png|alt=SR505n-Settings-Update- Running Settings|none|thumb|916x916px|SR505n-Settings-Update-Running Settings]]
4. Once the file upload begins, it can take 2 to 5 minutes to be completed and for your modem to be fully connected online. Resist the urge to make changes to the modem's configuration during this time.
[[File:SR505n-Update.png|alt=SR505n-Update- Upload in progress|none|thumb|724x724px|SR505n-Update- Upload in progress]]


=Configure for Routed Operation with WiFi=
=Routed Operation with Wi-Fi=
The SmartRG SR505n modem router supports both ADSL mode and VDSL mode. Provided it is configured correctly, it can be switched between ADSL and VDSL plans without the owner having to buy a new modem or even reconfigure your existing one.
{{Template:Back_to_the_Top}}
* Note: Fees for changing plans may still apply. Consult: [[DSL Rates]]
{{Template:SmartRG Config Options}}


== Checklist ==
== Checklist ==
Line 25: Line 48:


{| class="wikitable mw-collapsible"
{| class="wikitable mw-collapsible"
|+SmartRG SR505n Configuration Checklist
|+Steps to Configure SR505N for Routed Operation
!
!
!Configuration Steps
!Steps
!Menu Navigation
!Menu Navigation
!Key Parameters
!Parameters
!Check
|-
|-
|.2
|2
|[[#Log into Modem Web Interface|Log into Modem]]  
|[[#Log into Modem Web Interface|Log into Modem]]  
|<nowiki>http://192.168.1.1</nowiki>
|<nowiki>http://192.168.1.1</nowiki>
Line 40: Line 62:


Password: '''admin'''
Password: '''admin'''
|
|-
|-
|.3
|3
|[[#WAN Cleanup|WAN Cleanup]]
|[[#WAN Cleanup|WAN Cleanup]]
|'''Advanced Setup'''
|'''Advanced Setup'''
'''→ WAN Service'''
'''→ WAN Service'''
|Remove '''ppp0.1''' from '''WAN''' Service Table
|Remove '''ppp0.1''' from '''WAN''' Service Table
|&#9744;
|-
|-
|.4
|4
|[[#Enable ADSL Interface|Enable ADSL]]
|[[#Enable ADSL Interface|Enable ADSL]]
|'''Advanced Setup'''  
|'''Advanced Setup'''  
Line 57: Line 77:
|Add ATM: vpi:'''0''' vci:'''35'''
|Add ATM: vpi:'''0''' vci:'''35'''
DSL Latency: '''FAST''' and '''INTERLEAVED'''
DSL Latency: '''FAST''' and '''INTERLEAVED'''
|&#9744;
|-
|-
|.5
|5
|[[#Enable VDSL Interface|Enable VDSL]]
|[[#Enable VDSL Interface|Enable VDSL]]
|'''Advanced Setup'''
|'''Advanced Setup'''
'''→ Layers2 Interface'''
'''→ Layer2 Interface'''


'''→ PTM Interface'''
'''→ PTM Interface'''
Line 68: Line 87:
Add PTM:  
Add PTM:  
DSL Latency: '''FAST''' and '''INTERLEAVED'''
DSL Latency: '''FAST''' and '''INTERLEAVED'''
|&#9744;
|-
|-
|6.
|6
|[[#Configure ADSL Interface|Configure ADSL]]
|[[#Configure ADSL Interface|Configure ADSL]]
|'''Advanced Setup'''
|'''Advanced Setup'''
'''→ WAN Service'''
'''→ WAN Service'''
|Add '''atm0/(4_0_35)'''
|Add '''atm0/(4_0_35)'''             PPPoE (pppoe_4_0_35)
PPPoE (pppoe_4_0_35)
* Network Protocol Selection: '''IPv4 and IPv6 (Dual Stack)'''
* Network Protocol Selection: '''IPv4 and IPv6 (Dual Stack)'''
 
PPPoE username: your NCF account ID (format: '''xx000@ncf.ca''')  
* PPPoE username: your DSL username (format: aa000@ncf.ca)
 
* PPPoE password: your DSL password


PPPoE password: your DSL password
* Enable '''Firewall'''
* Enable '''Firewall'''


Line 85: Line 104:


* Disable '''SIP'''
* Disable '''SIP'''
|&#9744;
|-
|-
|.7
|7
|[[#Configure VDSL Interface|Configure VDSL]]
|[[#Configure VDSL Interface|Configure VDSL]]
|'''Advanced Setup'''
|'''Advanced Setup'''
'''→ WAN Service'''
'''→ WAN Service'''
|Add '''ptm0/(4_1_1)'''
|Add '''ptm0/(4_1_1)'''               PPPoE(pppoe_4_1_1.35)
PPPoE(pppoe_4_1_1)
* 802.1P Priority:'''1'''  
* 802.1P Priority:'''1'''  


* 802.1Q VLAN:'''35'''
* 802.1Q VLAN:'''35'''


* Network Protocol Selection: '''IPv4 and IPv6 (Dual Stack)'''
* Network Protocol Selection: '''IPv4 and IPv6 (Dual Stack)'''
PPPoE username: your NCF account ID (format: '''xx000@ncf.ca''')  
 
* PPPoE username: your DSL username (format: aa000@ncf.ca)
 
* PPPoE password: your DSL password


PPPoE password: your DSL password
* Enable '''Firewall'''
* Enable '''Firewall'''


Line 106: Line 125:


* Disable '''SIP'''
* Disable '''SIP'''
|&#9744;
|-
|-
|.8
|8
|[[#UPnP|UPnP]]
|[[#UPnP|UPnP]]
|'''Advanced Setup'''
|'''Advanced Setup'''
'''→ UPnP'''
'''→ UPnP'''
|Disable '''uPnP'''
|Disable '''uPnP'''
|&#9744;
|-
|-
|.9
|9
|[[SmartRG SR505N Configuration#WiFi Name|WiFi Name]]
|[[SmartRG SR505N Configuration#WiFi Name|WiFi Name]]
|'''Wireless'''
|'''Wireless'''
|SSID (WiFi Name) to format '''NCF_0000'''
|SSID (Wi-Fi Name) to format '''NCF_0000'''
|&#9744;
|-
|-
|.10
|10
|[[#WiFi Security|WiFi Security]]
|[[#WiFi Security|WiFi Security]]
|'''Wireless'''
|'''Wireless'''
Line 130: Line 146:
* WPA Passphrase : your DSL password
* WPA Passphrase : your DSL password
* WPA Encryption : '''AES'''
* WPA Encryption : '''AES'''
|&#9744;
|-
|-
|.11
|11
|[[SmartRG SR505N Configuration#Admin Password|Admin Password]]
|[[SmartRG SR505N Configuration#Admin Password|Admin Password]]
|'''Management'''
|'''Management'''
Line 143: Line 158:
* Old Password: admin (or whatever you set it to)
* Old Password: admin (or whatever you set it to)
* New Password: your DSL password
* New Password: your DSL password
|&#9744;
|-
|-
|.12
|12
|[[#Disable Support|Disable Support]]
|[[#Disable Support|Disable Support]]
|'''Management'''
|'''Management'''
'''→ Access Controls'''
'''→ Accounts'''
'''→ Accounts'''


'''Delete/Modify Account'''
|'''Delete/Modify Account'''
|Select '''Support''' role
* Select '''Support''' role
 
* '''Disable'''
* '''Disable'''
|&#9744;
* '''Update''' (at bottom)
|-
|-
|.13
|13
|[[#Remote Access|Remote Access]]
|[[#Remote Access|Remote Access]]
|'''Management'''
|'''Management'''
Line 163: Line 180:
* TR-069 Client: '''Disable'''
* TR-069 Client: '''Disable'''
* ACS URL: '''https://acs.ncf.ca'''
* ACS URL: '''https://acs.ncf.ca'''
* Connection Request Authentication: '''Unchecked'''
|&#9744;
|-
|-
|.14
|14
|[[#System Log|System Log]]
|[[#System Log|System Log]]
|'''Management'''
|'''Management'''
Line 176: Line 191:
* Display Level: '''Error'''
* Display Level: '''Error'''
* Mode: '''Local'''
* Mode: '''Local'''
|&#9744;
|-
|-
|.15
|15
|[[#Internet Time|Internet Time]]
|[[#Internet Time|Internet Time]]
|'''Management'''
|'''Management'''
Line 185: Line 199:
|
|
* First NTP time server: '''Other :''' '''time.nrc.ca'''
* First NTP time server: '''Other :''' '''time.nrc.ca'''
|&#9744;
|-
|-
|.16
|16
|[[#Backup Settings|Backup Settings]]
|[[#Backup Settings|Backup Settings]]
|'''Management'''
|'''Management'''
Line 197: Line 210:
* '''Backup''' '''Running Settings'''
* '''Backup''' '''Running Settings'''
* Save backup file to computer
* Save backup file to computer
|&#9744;
|}
|}


Line 291: Line 303:


== UPnP ==
== UPnP ==
UPnP allows devices on your network to automatically forward ports so they can be accessed from the Internet.  While UPnP is convenient, we recommend turning it off for security reasons.
{{Template:Back_to_the_Top}}23. From the '''Advanced Setup''' on the left, then Select '''UPnP'''. On the '''UPnP Configuration''' page,  
{{Template:Back_to_the_Top}}23. From the '''Advanced Setup''' on the left, then Select '''UPnP'''. On the '''UPnP Configuration''' page,  
* Uncheck the '''Enable UPnP''' box,
* Uncheck the '''Enable UPnP''' box,
Line 296: Line 309:
[[File:SR505n-Secure-UPnP.png|alt=SR505n-Secure- Disable UPnP|none|thumb|485x485px|SR505n-Secure- Disable UPnP]]
[[File:SR505n-Secure-UPnP.png|alt=SR505n-Secure- Disable UPnP|none|thumb|485x485px|SR505n-Secure- Disable UPnP]]


== WiFi Name==
== Wi-Fi Name==
{{Template:Back_to_the_Top}}
{{Template:Back_to_the_Top}}
24. Click and on '''Wireless''' menu link. From the Wireless - - Basic Page...
24. Click and on '''Wireless''' menu link. From the Wireless - - Basic Page...
Line 302: Line 315:
'''Note:'''  We recommend that you not use your name or address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
'''Note:'''  We recommend that you not use your name or address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
* Click on '''Apply/Save''' at the bottom.
* Click on '''Apply/Save''' at the bottom.
[[File:SR505n-WiFi.png|alt=SR505n-WiFi SSID Setup|none|thumb|631x631px|SR505n-WiFi SSID Setup]]25.Click on the '''Security''' link, under the '''Wireless''' Menu option.
[[File:SR505n-WiFi.png|alt=SR505n-WiFi SSID Setup|none|thumb|631x631px|SR505n-WiFi SSID Setup]]
== WiFi Security==
== Wi-Fi Security==
{{Template:Back_to_the_Top}}
{{Template:Back_to_the_Top}}25.Click on the '''Security''' link, under the '''Wireless''' Menu option.
* Set the '''Network Authentication''' to '''WPA2-PSK'''
* Set the '''Network Authentication''' to '''WPA2-PSK'''
* Set the '''WPA passphrase''' to be your DSL-Password
* Set the '''WPA passphrase''' to be your DSL-Password
Line 350: Line 363:


==Internet Time==
==Internet Time==
{{Template:Back_to_the_Top}}33. Click on '''Management''' and on '''Internet Time'''. Make the follow changes:
{{Template:Back_to_the_Top}}34. Click on '''Management''' and on '''Internet Time'''. Make the follow changes:
* Set '''First NTP time server''' to '''Other'''  and input the url '''time.nrc.ca''' in the adjacent textbox.
* Set '''First NTP time server''' to '''Other'''  and input the url '''time.nrc.ca''' in the adjacent textbox.
* Click '''Apply/Save'''
* Click '''Apply/Save'''
Line 356: Line 369:


==Backup Settings==
==Backup Settings==
{{Template:Back_to_the_Top}}34. Finally, back up your settings in case your modem is accidentally reset or if you need to return this configuration.  
{{Template:Back_to_the_Top}}35. Finally, back up your settings in case your modem is accidentally reset or if you need to return this configuration.  
* Click on '''Management''' and then '''Settings''' and then '''Backup'''.
* Click on '''Management''' and then '''Settings''' and then '''Backup'''.
* Then click on '''Backup Running Settings'''
* Then click on '''Backup Running Settings'''
Line 362: Line 375:
[[File:SR505n-Settings-Backup.png|alt=SR505n-Settings-Backup|none|thumb|640x640px|SR505n-Settings-Backup]]
[[File:SR505n-Settings-Backup.png|alt=SR505n-Settings-Backup|none|thumb|640x640px|SR505n-Settings-Backup]]


= Configure as Bridge=
= Routed Operation with separate Wi-Fi Router=
{{Template:Back_to_the_Top}}
{{Template:Back_to_the_Top}}
Do this only if you prefer to use your own external router rather than the one built into your SmartRG unit.
{{Template:SmartRG Config Options}}
 
==Configure your modem for Routed Operation==
If you have a router, we recommend the following configuration steps:
 
1. Follow the configuration steps outline for [[#Routed_Operation_with_WiFi|Routed Operation with WiFi]] and make the following changes:
* Under '''Wireless''', Uncheck the '''Enable Wireless''' Option,
* Click '''Apply/Save'''[[File:SR505n-Wireless-Disabled.png|alt=SR505n-Wireless-Disabled|none|thumb|560x560px|SR505n-Wireless-Disabled]]
 
==Router Configuration==
2. On your router, set the Connection Mode or Type to '''Automatic IP, Automatic DHCP or Dynamic IP mode'''.
 
= Bridge Operation=
{{Template:Back_to_the_Top}}
{{Template:SmartRG Config Options}}
 
If you prefer your own external router rather than the one built into your SmartRG unit, we recommend [[#Routed Operation with separate WiFi Router|routed operation with a separate WiFi Router]]. However if you have networking expertise and are confident using the modem in bridge mode then take note of the following before configuring your SmartRG for Bridged operation:
# Once you complete configuring your SmartRG modem for Bridged operation and disconnect from the modem, the Modem's Web Interface will become inaccessible with Auto DHCP settings on your computer. We recommend:
#* '''Backup Settings:''' It is particularly important to backup the '''Running Settings''' on your modem before and after you configure it.
#* '''Manual IP''': Setting a static IPv4 address on your computer, with the gateway IP set to http://192.168.1.1 to regain access to the modem
#* '''Reset the modem:''' If you need to reset the modem, insert a paper-clip in the '''Reset''' hole on the back. Hold for 10 seconds to reset.
#If you set up the modem for Bridge operation, then your router will need to be configured in PPPoE mode with your DSL username and password.
 
== Checklist ==
{{Template:Back_to_the_Top}}
 
{| class="wikitable mw-collapsible"
|+Steps to Configure SR505N for Bridge Operation
!
!Steps
!Menu Navigation
!Parameters
|-
|1
|[[#Log into Modem Web Interface|Log into Modem]]
|<nowiki>http://192.168.1.1</nowiki>
 
'''→ Manage Gateway (Advanced)'''
|User Name: '''admin'''
 
Password: '''admin'''
|-
|2
|[[#WAN Cleanup|WAN Cleanup]]
|'''Advanced Setup'''
'''→ WAN Service'''
|Remove '''ppp0.1''' from '''WAN''' Service Table
|-
|3
|[[#Enable ADSL Interface|Enable ADSL]]
|'''Advanced Setup'''
'''→ Layer2 Interface'''
 
'''→ ATM Interface'''
|Add ATM: vpi:'''0''' vci:'''35'''
DSL Latency: '''FAST''' and '''INTERLEAVED'''
|-
|4
|[[#Enable VDSL Interface|Enable VDSL]]
|'''Advanced Setup'''
'''→ Layers2 Interface'''


# Connect power and turn on the modem with the button on the back.
'''→ PTM Interface'''
# Connect an Ethernet LAN cable to one of the yellow rear ports
|Remove '''ptm0''' with '''Path0'''
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
Add PTM: DSL Latency: '''FAST''' and '''INTERLEAVED'''
# If the modem is fresh from the factory, use the default user name and password to gain access
|-
##'''user:''' admin
|6
##'''password:''' admin
|Configure ADSL
|'''Advanced Setup'''
'''→ WAN Service'''
|Add '''atm0/(4_0_35)'''            Bridge (br_4_0_35)
|-
|7
|Configure VDSL
|'''Advanced Setup'''
'''→ WAN Service'''
|Add '''ptm0/(4_1_1)'''              Bridge(br_4_1_1.35)
* 802.1P Priority:'''1'''


If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.
* 802.1Q VLAN:'''35'''
|-
|9
|WiFi
|'''Wireless'''
|Disable Wireless
|-
|11
|[[SmartRG SR505N Configuration#Admin Password|Admin Password]]
|'''Management'''
'''→ Access Controls'''


# Click on Advanced Setup and WAN Service and click on Add
'''→ Passwords'''
# The defaults are fine; click on Next.
|
# Click on Bridging and ensure the 802.1P and 802.1Q are set to 0 and 35, then click on Next.
* Username: '''admin'''
# Click on Apply/Save
# Done!


See screenshots below:
* Old Password: admin (or whatever you set it to)
* New Password: your DSL password
|-
|12
|[[#Disable Support|Disable Support]]
|'''Management'''
'''→ Accounts'''
 
'''→ Access Controls'''
|'''Delete/Modify Account'''
* Select '''Support''' role
 
* '''Disable'''
* '''Update''' (at bottom)
|-
|13
|[[#Remote Access|Remote Access]]
|'''Management'''
 
'''→ Management Server'''
|
* TR-069 Client: '''Disable'''
* ACS URL: '''https://acs.ncf.ca'''
|-
|14
|[[#System Log|System Log]]
|'''Management'''
 
'''→ System Log'''
|Configure System Log
* System Log:'''Enable'''
* Log Level: '''Debugging'''
* Display Level: '''Error'''
* Mode: '''Local'''
|-
|16
|[[#Backup Settings|Backup Settings]]
|'''Management'''
 
'''→ Settings'''
 
'''→ Backup'''
|
* '''Backup''' '''Running Settings'''
* Save backup file to computer
|}


=Firmware=
=Firmware=
{{Template:Back_to_the_Top}}
{{Template:Back_to_the_Top}}
'''We recommend that you only do firmware update over an ethernet connection and NOT via wifi. Also DO NOT power off the modem in the middle of a firmware update'''


The current firmware available to the NCF Office is 2.5.0.14. You can verify your firmware by checking the software version on the Device Info page.
{{Template:Firmware Caution}}
 
The current firmware available to the NCF Office is '''2.6.2.6'''.  
 
You can verify your firmware by checking the software version on the Device Info page. '''&#x26A0;Caution: Modems with firmware older than version 2.5.0.14 must be first upgraded to version 2.5.0.14 before upgrading to version 2.6.2.6. Failure to do so may cause functionality problems which will not be covered by the manufacturer's warranty.'''
[[File:SR505n-firmware-version.png|alt=SmartRG SR505n Firmware version check on Device Info Page|none|thumb|566x566px|SmartRG SR505n Firmware version check on Device Info Page]]
[[File:SR505n-firmware-version.png|alt=SmartRG SR505n Firmware version check on Device Info Page|none|thumb|566x566px|SmartRG SR505n Firmware version check on Device Info Page]]
To request a copy of this firmware email [[mailto:support@ncf.ca support@ncf.ca]]. To install this new firmware onto your modem perform the following steps:
To request firmware, email [[mailto:support@ncf.ca support@ncf.ca]]. To install this new firmware onto your modem perform the following steps:


# Download the firmware file and save it to a location on your computer that you can find easily.
# Download the firmware file and save it to a location on your computer that you can find easily.
Line 406: Line 545:
*[[Modem Lights#SmartRG|About SmartRG modem lights]]
*[[Modem Lights#SmartRG|About SmartRG modem lights]]
*[http://www.ncf.ca/ncf/dsl/modem/SmartRG_3xx-5xx_Gateway_User_Manual.pdf SmartRG SR505N modem manual]
*[http://www.ncf.ca/ncf/dsl/modem/SmartRG_3xx-5xx_Gateway_User_Manual.pdf SmartRG SR505N modem manual]
*[https://www.ncf.ca/ncf/support/w/images/f/f8/Modem_Info_Pages_-_SmartRG_505n_v1.0.pdf NCF SmartRG SR505N modem instruction sheet]
*[https://www.ncf.ca/ncf/support/w/images/8/86/About_Your_SmartRG_SR505n.pdf About Your SmartRG SR505n]
*[https://www.ncf.ca/ncf/support/w/images/7/79/Changing_Wireless_Channels_on_SmartRG_SR505N.pdf SmartRG SR505N Changing WiFi Channels]
*[[Changing WiFi Channels on SmartRG modems]]
*[[Dynamic DNS]]
*[[Dynamic DNS]]
*[[Port forwarding#Port_forwarding_on_SmartRG_Modems|Port forwarding with the SmartRG SR505N]]
*[[Port forwarding#Port_forwarding_on_SmartRG_Modems|Port forwarding with the SmartRG SR505N]]

Latest revision as of 17:41, 15 December 2023

Preparation

Updated: 2020-09-08

Recommended Firmware Version: 2.6.2.6. Please see the Firmware section below for more details.

The SmartRG SR505n modem router supports both ADSL mode and VDSL mode. Provided it is configured correctly, it can be switched between ADSL and VDSL plans without the owner having to buy a new modem or even re-configure your existing one.

  • Note: Fees for changing plans may still apply. Consult: DSL Rates

Before you start configuring the SmartRG SR505n, there are 4 things to check:

  1. Firmware Check: Check if you're using older firmware and upgrade to the recommended firmware version. If you're unable to access the internet to request newer firmware, note that the screenshots shown and steps outlined may not align with what you see. Contact the support@ncf.ca for assistance if you run into problems.
  2. Factory Settings and Standard Configuration: These instructions assume you're configuring SmartRG SR505n modem out of the box or after a factory reset. If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the reset button with a paper clip for ~10 seconds.
    • Also, these settings are our recommendations for most NCF members. To learn more about making custom changes to your particular modem, consult the manual.
  3. Modem Installation - Configure over Ethernet: Consult the SmartRG SR505N modem instruction sheet (page 1) on how to set up the modem and connect to it over ethernet. We do not recommend configuring your modem over a Wi-Fi connection.
  4. Configurations Methods: The 2 main ways of configuring the SmartRG SR505n modem:
    • Using a custom configuration File: You can request an NCF custom configuration file for your NCF DSL connection from support@ncf.ca (available to NCF members only)
    • Manually following configuration steps.
  5. Configuration Options:

Using Custom Configuration File

Your SmartRG modem can be configured for Routed or Bridged Operation by a custom configuration file. The custom configuration will include parameters specific to your NCF account.

1. Request a custom configuration file from support@ncf.ca and save it at a location you will remember.

Log into Modem Web Interface

2. Enter http://192.168.1.1 info the address bar at in your web browser. Click on Manage Gateway (advanced) and login with username: admin and password: admin (if your modem has been properly reset. If not try your NCF DSL password).

SmartRG SR505n Login Page
SmartRG SR505n Login Page

Uploading the File

3. Go to the Management Menu link, and then click on the Settings sub-menu link and then on the Update.

  • Click on the Browse link (in the Update Running Broadband Router Settings section) and navigate to the custom configuration file you saved.
  • Click on Update Running Settings.
SR505n-Settings-Update- Running Settings
SR505n-Settings-Update-Running Settings

4. Once the file upload begins, it can take 2 to 5 minutes to be completed and for your modem to be fully connected online. Resist the urge to make changes to the modem's configuration during this time.

SR505n-Update- Upload in progress
SR505n-Update- Upload in progress

Routed Operation with Wi-Fi

NCF Support is available to make configuring your SmartRG modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your SmartRG modem:

  1. You can request a custom configuration file for your NCF DSL connection from support@ncf.ca.
    • You may need an alternate means of accessing the internet to download the configuration file.
  2. Call 613-721-1773 x0 to book a Modem Appointment.

Checklist

Steps to Configure SR505N for Routed Operation
Steps Menu Navigation Parameters
2 Log into Modem http://192.168.1.1

→ Manage Gateway (Advanced)

User Name: admin

Password: admin

3 WAN Cleanup Advanced Setup

→ WAN Service

Remove ppp0.1 from WAN Service Table
4 Enable ADSL Advanced Setup

→ Layer2 Interface

→ ATM Interface

Add ATM: vpi:0 vci:35

DSL Latency: FAST and INTERLEAVED

5 Enable VDSL Advanced Setup

→ Layer2 Interface

→ PTM Interface

Remove ptm0 with Path0

Add PTM: DSL Latency: FAST and INTERLEAVED

6 Configure ADSL Advanced Setup

→ WAN Service

Add atm0/(4_0_35) PPPoE (pppoe_4_0_35)
  • Network Protocol Selection: IPv4 and IPv6 (Dual Stack)
  • PPPoE username: your DSL username (format: aa000@ncf.ca)
  • PPPoE password: your DSL password
  • Enable Firewall
  • Enable NAT
  • Disable SIP
7 Configure VDSL Advanced Setup

→ WAN Service

Add ptm0/(4_1_1) PPPoE(pppoe_4_1_1.35)
  • 802.1P Priority:1
  • 802.1Q VLAN:35
  • Network Protocol Selection: IPv4 and IPv6 (Dual Stack)
  • PPPoE username: your DSL username (format: aa000@ncf.ca)
  • PPPoE password: your DSL password
  • Enable Firewall
  • Enable NAT
  • Disable SIP
8 UPnP Advanced Setup

→ UPnP

Disable uPnP
9 WiFi Name Wireless SSID (Wi-Fi Name) to format NCF_0000
10 WiFi Security Wireless

→ Security

  • Disable WPS
  • Network Authentication to WPA2-PSK
  • WPA Passphrase : your DSL password
  • WPA Encryption : AES
11 Admin Password Management

→ Access Controls

→ Passwords

  • Username: admin
  • Old Password: admin (or whatever you set it to)
  • New Password: your DSL password
12 Disable Support Management

→ Access Controls

→ Accounts

Delete/Modify Account
  • Select Support role
  • Disable
  • Update (at bottom)
13 Remote Access Management

→ Management Server

14 System Log Management

→ System Log

Configure System Log
  • System Log:Enable
  • Log Level: Debugging
  • Display Level: Error
  • Mode: Local
15 Internet Time Management

→ Internet Time

  • First NTP time server: Other : time.nrc.ca
16 Backup Settings Management

→ Settings

→ Backup

  • Backup Running Settings
  • Save backup file to computer

Log into Modem Web Interface

1. Enter http://192.168.1.1 info the address bar at in your web browser. Click on Manage Gateway (advanced) and login with username: admin and password: admin (if your modem has been properly reset. If not try your NCF DSL password).

SmartRG SR505n Login Page
SmartRG SR505n Login Page

WAN Cleanup

2. Click on the Advanced Setup menu, then on the WAN Service sub-menu. Select the Remove checkbox on the ppp0.1 interface listed on WAN Service Setup table and click Remove at the bottom of the page.

Remove SR505n Default WAN Service
Remove SR505n Default WAN Service

Enable ADSL Interface

3. Under the Advanced Setup menu, click on the Layer2 Interface and then ATM Interface. Click Add and proceed

SR505n ATM add page
SR505n ATM add page

4. On the ATM PVC Configuration page, select the following:

  • VPI:0 and VPI:35
  • DSL Latency: Select both
    • Path0(fast)
    • Path1(interleaved)
  • Apply/Save
SR505n Configure ATM interface
SR505n Configure ATM interface

5. Confirm you have configured the ADSL (ATM) interface correctly with the image below:

SR505n confirm ATM configuration
SR505n confirm ADSL (ATM) Interface Setup

Enable VDSL Interface

6. Under the Advanced Setup menu, click on the Layer2 Interface and then PTM Interface. Select the Remove checkbox on the ptm0 interface and click Remove.

SR505n - Remove FAST only PTM interface
SR505n - Remove FAST only PTM interface

7. Still on the DSL PTM Interface Configuration Page, Click Add and proceed.

SR505n- add new PTM interface
SR505n- add new PTM interface

8. On the PTM Configuration page, select the following:

  • DSL Latency: Select both
    • Path0(fast)
    • Path1(interleaved)
  • Apply/Save
SR505n- Configure new PTM interface
SR505n- Configure new PTM interface

9. Confirm you have configured the VDSL (PTM) interface correctly with the image below:

SR505n - Confirm VDSL (PTM) Interface Setup
SR505n - Confirm VDSL (PTM) Interface Setup

Configure ADSL Interface

10. From Advanced Setup, click on WAN Service and then click on Add to proceed.

SR505n- Add WAN(PPPoE) ADSL configuration
SR505n- Add WAN(PPPoE) ADSL configuration

11. On the WAN Service Interface Configuration page, select atm0/(4_0_35) from the drop-down menu and click Next.

SR505n- Mapping atm0 to WAN(PPPoE) ADSL configuration
SR505n- Mapping atm0 to WAN ADSL configuration

12. On the WAN Service Configuration page, ensure the following:

  • PPP over Ethernet (PPPoE) is the active WAN service type chosen,
  • Ensure Service Description shows as pppoe_4_0_35,
  • Network Protocol Selection is set to IPv4&IPv6(Dual Stack), and click Next
SR505n- PPPoE WAN Service Type and IP Protocol
SR505n- PPPoE WAN Service Type and IP Protocol

13. On the PPP Username and Password page, enter your DSL username (format xx000@ncf.ca) and your DSL password into the PPP Username and PPP Password fields respectively. Scroll down the page...

SR505n- Enter PPPoE/DSL credentials for WAN-ADSL
SR505n- Enter PPPoE/DSL credentials for WAN-ADSL

14. Ensure Enable Firewall, Enable NAT are checked.

  • Ensure Enable SIP is not checked. Note on SIP: Although we've found that most most VOIP providers prefer to have SIP disabled on modem/routers, your VOIP provider may require this feature. If you're encountering VOIP issues, confirm this setting preference with your VOIP provider.
  • Scroll to the bottom of the page and click Next
SR505n- Enable Firewall and NAT on WAN-ADSL
SR505n-  Enable Firewall and NAT on WAN-ADSL

15. Click on Next twice on the Routing - Default Gateway and DNS Server Configuration pages to skip to the WAN Setup - Summary page.

  • Verify that the summary information you see matches the table below,
  • Click on Apply/Save
SR505n- Summary Settings for WAN-ADSL
SR505n- Summary Settings for WAN-ADSL

Configure VDSL Interface

16. Back on the WAN Service page, click on Add to proceed.

SR505n- Add WAN(PPPoE) VDSL configuration
SR505n- Add WAN(PPPoE) VDSL configuration

17. On the WAN Service Interface Configuration page, select ptm0/(4_1_1) from the drop-down menu and click Next.

SR505n- Mapping ptm0 to WAN(PPPoE) VDSL configuration
SR505n- Mapping ptm0 to WAN VDSL configuration

18. On the WAN Service Configuration page, ensure the following:

  • PPP over Ethernet (PPPoE) is the active WAN service type chosen,
  • Ensure Service Description shows as pppoe_4_1_1,
  • 802.1P Priority is set to 1
  • 802.1Q VLAN ID is set to 35
  • Network Protocol Selection is set to IPv4&IPv6(Dual Stack), and click Next
SR505n- PPPoE WAN Service Type, Priority, VLAN ID and IP Protocol
SR505n- PPPoE WAN Service Type, Priority, VLAN ID and IP Protocol

19. On the PPP Username and Password page, enter your DSL username (format xx000@ncf.ca) and your DSL password into the PPP Username and PPP Password fields respectively. Scroll down the page...

SR505n- Enter PPPoE/DSL credentials for WAN-VDSL
SR505n- Enter PPPoE/DSL credentials for WAN-VDSL

20. Ensure Enable Firewall, Enable NAT are checked.

  • Ensure Enable SIP is not checked. Note on SIP: Although we've found that most most VOIP providers prefer to have SIP disabled on modem/routers, your VOIP provider may require this feature. If you're encountering VOIP issues, confirm this setting preference with your VOIP provider.
  • Scroll to the bottom of the page and click Next
SR505n- Enable Firewall and NAT on WAN-VDSL
SR505n- Enable Firewall and NAT on WAN-VDSL

21. Click on Next twice on the Routing - Default Gateway and DNS Server Configuration pages to skip to the WAN Setup - Summary page.

  • Verify that the summary information you see matches the table below,
  • Click on Apply/Save.
SR505n- Summary Settings for WAN-VDSL
SR505n- Summary Settings for WAN-VDSL

22. Confirm that the table on the Wide Area Network (WAN) Service Setup page match the image below and proceed.

SR505n- Confirmation WAN Service Setup Table
SR505n- Confirmation WAN Service Setup Table

UPnP

UPnP allows devices on your network to automatically forward ports so they can be accessed from the Internet. While UPnP is convenient, we recommend turning it off for security reasons.

23. From the Advanced Setup on the left, then Select UPnP. On the UPnP Configuration page,

  • Uncheck the Enable UPnP box,
  • Save the changes with Apply/Save
SR505n-Secure- Disable UPnP
SR505n-Secure- Disable UPnP

Wi-Fi Name

24. Click and on Wireless menu link. From the Wireless - - Basic Page...

  • Set the SSID is set to NCF_0000 (NCF uses the last 4 digits of the modem's serial number).

Note: We recommend that you not use your name or address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.

  • Click on Apply/Save at the bottom.
SR505n-WiFi SSID Setup
SR505n-WiFi SSID Setup

Wi-Fi Security

25.Click on the Security link, under the Wireless Menu option.

  • Set the Network Authentication to WPA2-PSK
  • Set the WPA passphrase to be your DSL-Password
  • Set the WPA Ecryption to AES
  • Click Apply/save.
SR505n-WiFi-Security Settings
SR505n-WiFi-Security Settings

Admin Password

26. Click on Management on the left. Then click on Access Control to reveal a sub-menu and then click on Passwords.

  • Enter admin for the User Name
  • Enter admin for the Old Password
  • Enter your DSL-Password or another strong password as the New Password.
  • Enter it once and again below to confirm
  • Save the changes with Apply/Save
SR505n-Secure-Admin Password Change
SR505n-Secure-Admin Password Change

27. On Click on Management again, a pop-up log-in screen appears, and asks for sign-in. Use the User-ID admin and the DSL-Password just set.

Disable Support

28. Click on Access Control again and then select the Accounts sub-menu link. Then on the User Access Control Settings page, click on Delete/Modify Account.

SR505n-Secure-Accounts Page
SR505n-Secure-Accounts Page

29. On the Delete/Edit Account page, ensure the selected account is support and selected Disable.

  • Click Update Account at the bottom of the page and then click Back.
SR505n-Secure-Disable Support
SR505n-Secure-Disable Support

30. Confirm your User Access Control Settings display as follows

SR505n-Secure-Accounts- Confirm Support is Disabled
SR505n-Secure-Accounts- Confirm Support is Disabled

Remote Access

31. Click on Management and then on Management Server. On the TR-069 Client -- Configuration page, perform the following changes:

  • Set to TR-069 Client to Disable,
  • Change the ACS URL to https://acs.ncf.ca,
  • Uncheck Connection Request Authentication, and
  • Apply/Save
SR505n-Secure- Disable Remote Access
SR505n-Secure- Disable Remote Access

System Log

32. Click on Management and on System Log.

SR505n- System Log
SR505n- System Log

33. Ensure the following settings:

  • Log is Enable
  • Log Level is Debugging
  • Display Level is Error
  • Mode is Local
  • Click Apply/Save
SR505n- System Log Configuration
SR505n- System Log Configuration

Internet Time

34. Click on Management and on Internet Time. Make the follow changes:

  • Set First NTP time server to Other and input the url time.nrc.ca in the adjacent textbox.
  • Click Apply/Save
SR505n-InternetTime
SR505n-InternetTime

Backup Settings

35. Finally, back up your settings in case your modem is accidentally reset or if you need to return this configuration.

  • Click on Management and then Settings and then Backup.
  • Then click on Backup Running Settings
  • Save the back up file to a location you will remember. We recommend including the date and your account ID in the name of the file.
SR505n-Settings-Backup
SR505n-Settings-Backup

Routed Operation with separate Wi-Fi Router

NCF Support is available to make configuring your SmartRG modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your SmartRG modem:

  1. You can request a custom configuration file for your NCF DSL connection from support@ncf.ca.
    • You may need an alternate means of accessing the internet to download the configuration file.
  2. Call 613-721-1773 x0 to book a Modem Appointment.

Configure your modem for Routed Operation

If you have a router, we recommend the following configuration steps:

1. Follow the configuration steps outline for Routed Operation with WiFi and make the following changes:

  • Under Wireless, Uncheck the Enable Wireless Option,
  • Click Apply/Save
    SR505n-Wireless-Disabled
    SR505n-Wireless-Disabled

Router Configuration

2. On your router, set the Connection Mode or Type to Automatic IP, Automatic DHCP or Dynamic IP mode.

Bridge Operation

NCF Support is available to make configuring your SmartRG modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your SmartRG modem:

  1. You can request a custom configuration file for your NCF DSL connection from support@ncf.ca.
    • You may need an alternate means of accessing the internet to download the configuration file.
  2. Call 613-721-1773 x0 to book a Modem Appointment.

If you prefer your own external router rather than the one built into your SmartRG unit, we recommend routed operation with a separate WiFi Router. However if you have networking expertise and are confident using the modem in bridge mode then take note of the following before configuring your SmartRG for Bridged operation:

  1. Once you complete configuring your SmartRG modem for Bridged operation and disconnect from the modem, the Modem's Web Interface will become inaccessible with Auto DHCP settings on your computer. We recommend:
    • Backup Settings: It is particularly important to backup the Running Settings on your modem before and after you configure it.
    • Manual IP: Setting a static IPv4 address on your computer, with the gateway IP set to http://192.168.1.1 to regain access to the modem
    • Reset the modem: If you need to reset the modem, insert a paper-clip in the Reset hole on the back. Hold for 10 seconds to reset.
  2. If you set up the modem for Bridge operation, then your router will need to be configured in PPPoE mode with your DSL username and password.

Checklist

Steps to Configure SR505N for Bridge Operation
Steps Menu Navigation Parameters
1 Log into Modem http://192.168.1.1

→ Manage Gateway (Advanced)

User Name: admin

Password: admin

2 WAN Cleanup Advanced Setup

→ WAN Service

Remove ppp0.1 from WAN Service Table
3 Enable ADSL Advanced Setup

→ Layer2 Interface

→ ATM Interface

Add ATM: vpi:0 vci:35

DSL Latency: FAST and INTERLEAVED

4 Enable VDSL Advanced Setup

→ Layers2 Interface

→ PTM Interface

Remove ptm0 with Path0

Add PTM: DSL Latency: FAST and INTERLEAVED

6 Configure ADSL Advanced Setup

→ WAN Service

Add atm0/(4_0_35) Bridge (br_4_0_35)
7 Configure VDSL Advanced Setup

→ WAN Service

Add ptm0/(4_1_1) Bridge(br_4_1_1.35)
  • 802.1P Priority:1
  • 802.1Q VLAN:35
9 WiFi Wireless Disable Wireless
11 Admin Password Management

→ Access Controls

→ Passwords

  • Username: admin
  • Old Password: admin (or whatever you set it to)
  • New Password: your DSL password
12 Disable Support Management

→ Accounts

→ Access Controls

Delete/Modify Account
  • Select Support role
  • Disable
  • Update (at bottom)
13 Remote Access Management

→ Management Server

14 System Log Management

→ System Log

Configure System Log
  • System Log:Enable
  • Log Level: Debugging
  • Display Level: Error
  • Mode: Local
16 Backup Settings Management

→ Settings

→ Backup

  • Backup Running Settings
  • Save backup file to computer

Firmware

SmartRG firmware update/s available to NCF members only. Firmware updates have been validated and tested against a custom configuration for NCF DSL members. Non-NCF requests will be disregarded.

Caution:

  • We recommend that you only do firmware updates over an Ethernet connection and NOT via Wi-Fi.
  • DO NOT power off the modem during a firmware update, as this will cause your modem become unresponsive (stuck in brick/recovery mode).

The current firmware available to the NCF Office is 2.6.2.6.

You can verify your firmware by checking the software version on the Device Info page. ⚠Caution: Modems with firmware older than version 2.5.0.14 must be first upgraded to version 2.5.0.14 before upgrading to version 2.6.2.6. Failure to do so may cause functionality problems which will not be covered by the manufacturer's warranty.

SmartRG SR505n Firmware version check on Device Info Page
SmartRG SR505n Firmware version check on Device Info Page

To request firmware, email [support@ncf.ca]. To install this new firmware onto your modem perform the following steps:

  1. Download the firmware file and save it to a location on your computer that you can find easily.
  2. Open a web browser and go to the address http://192.168.1.1
  3. Select Manage Gateway (Advanced) and log in (by default the username is admin and password is your dsl password as shown in Getting Started above)
  4. Click on ManagementUpdate Software
  5. Click on Browse
  6. Upload the firmware file that you downloaded in step 1.
  7. Click Update Software
SR505n firmware update
SR505n firmware update

Note: the modem will reboot once the new firmware has been uploaded. This process may take up to 15 minutes to resync (DSL light returns to solid green) and reconnect (the internet light starts blinking again).

See Also