Head blueLogoText.gif NCF HelpWiki
Help | StartPage

Difference between revisions of "Modem Installation"

From Support
Jump to navigation Jump to search
m
 
(36 intermediate revisions by 5 users not shown)
Line 1: Line 1:
__NOTOC__
<div class="ncfrightbox"> {{Template:Modem Links}} </div>


SpeedTouch DSL modems obtained from NCF are pre-configured and ready to install by following the steps below.  If your modem is not a SpeedTouch pre-configured by NCF, consult the [[manual configuration guide]].
DSL modems obtained from NCF are pre-configured and ready to install by following the steps below; you do not need to use the modem's Set-Up disk(If your modem is not pre-configured by NCF, consult the [[Modem Configuration|modem configuration guide]].)


== Installing a DSL Modem ==
=Install line filters=
Every device connected to the phone line at your location must have a line filter '''except the DSL modem'''.  Devices that must be connected via a filter include phones, fax machines, satellite receivers, alarm systems, and dial-up computer modems. Alternatively, you can use one filter for your entire location (see [[Home Wiring]]).


=== Step One: Install line filters ===
[[File:PhoneLineFilter.png|center|frame|Every device (except the DSL modem) needs a line filter]]
Every device connected to the phone line at your location must have a line filter <b>except the DSL modem</b>.  Devices that must be connected via a filter include phones, fax machines, satellite receiver, alarm system, and dial-up computer modems.  (Alterntively, you can [[use one filter for your entire location]].)


[[File:PhoneLineFilter.png|center|frame|Every device (except DSL modem) needs a line filter]]
=Connect the DSL modem=
Connect the DSL modem directly (with '''no filter''') to a phone jack using the supplied phone line cable and to your computer with an ethernet cable (if you are using ethernet). Plug in the modem power supply. For best performance, use only the phone line provided with the modem. Locate it away from sources of electrical interference and ensure that it has good ventilation for cooling.


=== Step Two: Install the DSL modem ===
[[File:DslModemPhoneComputer.png|center|frame|Connect modem to phone line and computer]]
Connect the DSL modem directly (with <b>no filter</b>) to a phone jack, and to your computer.  Plug in the modem power supply. [[Tips for best performance]].
 
=Power up the modem and use the Internet=
Turn the modem on using the push-button switch located on the back of the modem. The lights on the modem should come on right away and within a few minutes they should turn green.
 
If your modem is from NCF, it will be pre-configured and ready to go. Your computer should now be able to browse the internet. See [[Modem Lights]]


[[File:DslModemPhoneComputer.png|center|frame|Connect modem to phone line and computer]]
Normally DSL modems are left on continuously to ensure your connection is there when you need it. If you are going to be away from home for an extended period of time it can be turned off.


=== Step Three: Turn on the modem and use the internet ===
=Wireless=
Lights on the modem should come on and, within a few minutes, turn green.
If you have a modem that supports wireless access, it is pre-configured by NCF to operate with high security (WPA-PSK mode), which requires a password.  The green WLAN light on the modem indicates the modem is ready for wireless access, and the modem should now appear on the list of access points available to your computer. When you try to make a connection, you will need to provide the WPA-PSK key that is printed on the bottom of your modem (also printed on a label on your modem's Setup disk) in the case of SpeedTouch modems or using your NCF [[DSL password]] (all other types of modems). For more details about wireless, consult your [[Modem Manuals|modem's manual]].


If your modem is from NCF, it will be pre-configured and ready to go. Your computer should now be able to browse the internet.  [[About DSL modem lights]]
=Doing more=
DSL modems generally have features to support more than the standard operation enabled above. For special circumstances and doing more, have a look at the [[Modem Manuals|modem's manual]].


== Problems? ==
=Problems?=


The modem lights usually indicate what is wrong. [[About DSL modem lights]]
The modem lights usually indicate what is wrong. See [[Modem Lights]].


If your modem is not seeing a DSL signal (the DSL light is not becoming solid green within a few minutes), here are some possible solutions:
If your modem is not detecting a DSL signal, indicated by the DSL light not becoming solid green within a few minutes, here are some possible solutions:


* If this is a new installation, maybe Bell hasn't yet turned on DSL to your line. What day were you told DSL service could be expected to start (the 'activation date')?
* If this is a new installation, maybe Bell has not yet turned on the DSL service on your line. Which day were you told DSL service could be expected to start? (the 'activation date')


* Check the connections. Using a phone, make sure there is phone service to the wall jack where the modem is to be connected.
* Check the connections. Using a phone, make sure there is phone service to the wall jack where the modem is to be connected.


* Try a [[troubleshooting]] procedure.
* Try the [[Troubleshooting|troubleshooting]] procedures.


If there are still problems: [http://help.ncf.ca NCF Help].
If there are still problems: see [http://www.ncf.ca/ncf/support/ NCF Help] and especially [http://www.ncf.ca/ncf/dg/index.jsp?dg=82 the DSL Help Desk] discussion group.


== Related Links ==
=See also=
* one filter for the house
* [https://www.ncf.ca/ncf/support/w/images/9/91/Modem_Info_Pages_-_8951_v1.2.pdf NCF TP-Link 8951 installation instruction sheet]
* how filters work, what they do and why they are necessary
* [https://www.ncf.ca/ncf/support/w/images/a/a6/Modem_Info_Pages_-_8816_v1.5.pdf NCF TP-Link 8816 installation instruction sheet]
* modem manuals
* [https://www.ncf.ca/ncf/support/w/images/f/f8/Modem_Info_Pages_-_SmartRG_505n_v1.0.pdf NCF SmartRG 505n installation instruction sheet]
* how to config modem manually (how to connect to modem)
* [[ Configuring your computer (DSL)| Configuring your computer]]
* troubleshooting


[[Category:DSL]]
[[Category:DSL]]
[[Category:Modems]]

Latest revision as of 16:53, 28 July 2018

DSL modems obtained from NCF are pre-configured and ready to install by following the steps below; you do not need to use the modem's Set-Up disk. (If your modem is not pre-configured by NCF, consult the modem configuration guide.)

Install line filters

Every device connected to the phone line at your location must have a line filter except the DSL modem. Devices that must be connected via a filter include phones, fax machines, satellite receivers, alarm systems, and dial-up computer modems. Alternatively, you can use one filter for your entire location (see Home Wiring).

Every device (except the DSL modem) needs a line filter

Connect the DSL modem

Connect the DSL modem directly (with no filter) to a phone jack using the supplied phone line cable and to your computer with an ethernet cable (if you are using ethernet). Plug in the modem power supply. For best performance, use only the phone line provided with the modem. Locate it away from sources of electrical interference and ensure that it has good ventilation for cooling.

Connect modem to phone line and computer

Power up the modem and use the Internet

Turn the modem on using the push-button switch located on the back of the modem. The lights on the modem should come on right away and within a few minutes they should turn green.

If your modem is from NCF, it will be pre-configured and ready to go. Your computer should now be able to browse the internet. See Modem Lights

Normally DSL modems are left on continuously to ensure your connection is there when you need it. If you are going to be away from home for an extended period of time it can be turned off.

Wireless

If you have a modem that supports wireless access, it is pre-configured by NCF to operate with high security (WPA-PSK mode), which requires a password. The green WLAN light on the modem indicates the modem is ready for wireless access, and the modem should now appear on the list of access points available to your computer. When you try to make a connection, you will need to provide the WPA-PSK key that is printed on the bottom of your modem (also printed on a label on your modem's Setup disk) in the case of SpeedTouch modems or using your NCF DSL password (all other types of modems). For more details about wireless, consult your modem's manual.

Doing more

DSL modems generally have features to support more than the standard operation enabled above. For special circumstances and doing more, have a look at the modem's manual.

Problems?

The modem lights usually indicate what is wrong. See Modem Lights.

If your modem is not detecting a DSL signal, indicated by the DSL light not becoming solid green within a few minutes, here are some possible solutions:

  • If this is a new installation, maybe Bell has not yet turned on the DSL service on your line. Which day were you told DSL service could be expected to start? (the 'activation date')
  • Check the connections. Using a phone, make sure there is phone service to the wall jack where the modem is to be connected.

If there are still problems: see NCF Help and especially the DSL Help Desk discussion group.

See also