Head blueLogoText.gif NCF HelpWiki
Help | StartPage

Difference between revisions of "TP-Link TD-W8951ND Configuration"

From Support
Jump to: navigation, search
(shifted images)
(ACL: fixed)
(32 intermediate revisions by 5 users not shown)
Line 8: Line 8:
 
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
 
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
 
# If the modem is fresh from the factory, use the default user name and password to gain access
 
# If the modem is fresh from the factory, use the default user name and password to gain access
'''user:'''admin '''pwd:'''admin
+
##'''user:''' admin  
 +
##'''password:''' admin
  
If the modem was previously configured for someone, the password would be the previous user's DSL-Password. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 15 seconds to reset. The user name and password will now be as above.
+
If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 15 seconds to reset. The user name and password will now be as above.
  
# When presented with the TP-Link configuration page, select the '''Quick Setup''' option at the top left.
+
# When presented with the TP-Link configuration page, select the '''Quick Start''' option at the top left.
 
# Select '''Run Wizard''' to proceed.   
 
# Select '''Run Wizard''' to proceed.   
 
Now a window pops open and you can begin to set up the details of the interface.
 
Now a window pops open and you can begin to set up the details of the interface.
Line 35: Line 36:
 
Continuing now to set the '''wireless''' configuration
 
Continuing now to set the '''wireless''' configuration
 
# Ensure '''Access Point''' indicates '''activated'''
 
# Ensure '''Access Point''' indicates '''activated'''
# The '''SSID''' should be altered to start with '''NCF''' - so TP_Link_AA123A would become NCF_AA123A or some other identification so you can recognize and select it from your laptop or other wireless device. It is recommended you not use your first or last name as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
+
# The '''SSID''' is set to NCF plus a random number, such as '''NCF_123456'''. It is recommended you not use your first or last name, or street address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
 
# Broadcast SSID remains selected
 
# Broadcast SSID remains selected
# '''Auth Type''' - must be set to '''WPA-PSK/WPA2-PSK'''
+
# '''Auth Type''' - must be set to '''WPA2-PSK'''
 
...wait a moment for it to offer additional field for encryption and password...
 
...wait a moment for it to offer additional field for encryption and password...
  
# Set '''Encryption Type''' to be '''TKIP/AES'''
+
# Set '''Encryption Type''' to be '''AES'''
 
# Set the '''Preshared Key''' to be your DSL-Password
 
# Set the '''Preshared Key''' to be your DSL-Password
 
# Click '''Next''' to Finish the wizard.
 
# Click '''Next''' to Finish the wizard.
  
 
Proceed with four more steps - Setting administrator access, and wireless locale setting
 
Proceed with four more steps - Setting administrator access, and wireless locale setting
 +
 +
=== VoIP Enabling ===
 +
# Launch Telnet session from the computer command line.
 +
# Enter the following commands:
 +
## sys edit autoexec.net (press enter)
 +
## i (when you press i, it means inserting the following commands to the system)
 +
## ip nat service sip sw off (press enter)
 +
## x (press x)
  
 
=== Password protect the Admin Role ===  
 
=== Password protect the Admin Role ===  
Line 71: Line 80:
 
Still on this page, Verify:
 
Still on this page, Verify:
 
# The '''SSID''' in the form '''NCF_XXXXX''' or as you set.
 
# The '''SSID''' in the form '''NCF_XXXXX''' or as you set.
# The '''Auth Type''' is '''WPA-PSK/WPA2-PSK'''
+
# The '''Auth Type''' is '''WPA2-PSK'''
# The '''Encryption Type''' is '''TKIP/AES''' and key is DSL-Password
+
# The '''Encryption Type''' is '''AES''' and key is DSL-Password
 
# Click on the ''' Internet''' tab
 
# Click on the ''' Internet''' tab
 
# Ensure that PVC2 has VPI/VCI set at 0/35
 
# Ensure that PVC2 has VPI/VCI set at 0/35
# Ensure that PPPoE credentials are set properly for user@ncf.ca and password.
+
# Ensure that PPPoE credentials are set properly for your user name and password.
  
 
The modem should now synchronize and connect to your DSL service if the service is operating. You may need to reboot the modem to get it to connect.
 
The modem should now synchronize and connect to your DSL service if the service is operating. You may need to reboot the modem to get it to connect.
 +
 +
==Security==
 +
In January 2014 it was revealed that some models of TP-Link modem, including this model, are subject to hacking if they are running out dated firmware and if the remote access (ACL) is set to allow remote access. [[CERT-announced vulnerability of TP-Link modem/router|This web page]] provides more detailed information on the vulnerability. Latest firmware versions can be checked on the [http://www.tp-link.com/en/download/TD-W8951ND.html TP-Link website].
 +
 +
===ACL===
 +
#To be sure your modem is secure, click on "Access Management". By default the "ACL" tab will be active.
 +
#Ensure your ACL page looks like the screen shot below. If not, choose "WAN" from the "Interface" drop-down box.
 +
#Select "deactivated".
 +
#Click "Save".
 +
[[File:TP-Link modem with ACL deactivated.jpg|TP-Link modem with ACL deactivated]]
 +
 +
==See also==
 +
*[https://www.ncf.ca/ncf/support/w/images/9/91/Modem_Info_Pages_-_8951_v1.2.pdf NCF TP-Link 8951ND Instruction sheet]
 +
*[[CERT-announced vulnerability of TP-Link modem/router]]
 +
*[[Dynamic DNS]]
 +
*[[Modem Configuration (DSL)]] - for a complete list of instructions for all NCF modems
 +
*[[Port forwarding]]
 +
*[[VOIP]]
 
[[Category: DSL]]
 
[[Category: DSL]]

Revision as of 21:20, 31 January 2018

The TP-Link 8951ND modem

This is the procedure NCF uses to configure a TP-Link 8951ND modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the manual.

Configure as router

  1. Connect power and turn on the modem with the black button on the back.
  2. Connect an Ethernet LAN cable to one of the yellow rear ports
  3. In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
  4. If the modem is fresh from the factory, use the default user name and password to gain access
    1. user: admin
    2. password: admin

If the modem was previously configured for someone, the password would be the previous user's DSL password. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 15 seconds to reset. The user name and password will now be as above.

  1. When presented with the TP-Link configuration page, select the Quick Start option at the top left.
  2. Select Run Wizard to proceed.

Now a window pops open and you can begin to set up the details of the interface.

  1. Select Next to proceed
  2. Set the Time Zone Eastern
  3. Click Next
  4. Set the connection type of PPPoE/PPPoA
  5. Click Next
  6. Ensure VPI is set to 0 and VCI is set to 35
  7. Click Next
  8. Verify that PPPoverEthernet PPPoE is selected
  9. Click Next

DSL Quick Configuration Info
(TP-Link DSL modems)

Modem's URL:http://192.168.1.1
(click, or enter this in your browser)
Modem's login:Username: admin
Password: (see 'password' below)
VPI / VCI:0.35
Protocol:PPPoE
DSL username: Your NCF account ID (eg., aa999)
DSL password:Starts with 'ncf' (not the same as your NCF StartPage login)
Firewall:Enabled by default (leaving it on is recommended)
Wireless:If enabled, WPA-PSK (WPA2)

Continuing now to set the user name and password

  1. PPPoE Service name can remain blank
  2. PPP username in the form ab123@ncf.ca (NOTE the "@ncf.ca" part! - it will not work without that!)
  3. PPP Password uses DSL Password (This is not your NCF account password, but your DSL password and was provided to you when you signed up for service, it starts with "ncf...")
  4. Ensure that the encapsulation remains at PPPoE LLC (default)
  5. Click Next

Continuing now to set the wireless configuration

  1. Ensure Access Point indicates activated
  2. The SSID is set to NCF plus a random number, such as NCF_123456. It is recommended you not use your first or last name, or street address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
  3. Broadcast SSID remains selected
  4. Auth Type - must be set to WPA2-PSK

...wait a moment for it to offer additional field for encryption and password...

  1. Set Encryption Type to be AES
  2. Set the Preshared Key to be your DSL-Password
  3. Click Next to Finish the wizard.

Proceed with four more steps - Setting administrator access, and wireless locale setting

VoIP Enabling

  1. Launch Telnet session from the computer command line.
  2. Enter the following commands:
    1. sys edit autoexec.net (press enter)
    2. i (when you press i, it means inserting the following commands to the system)
    3. ip nat service sip sw off (press enter)
    4. x (press x)

Password protect the Admin Role

  1. Click on Maintenance in the menu along the top of the page. Below it other options appear.
  2. Select Administration
  3. For the admin user use your DSL-Password or another strong password.
  4. Enter it once and again below to confirm
  5. Save the changes with Save

A pop-up log-in screen appears, and asks for sign-in. Use the User-ID admin and the DSL-Password just set. Return to the same configure page you were just at.

Set daylight savings time

  1. In Maintenance select Time Zone.
  2. Daylight Saving: Enabled

Turn on SPI firewalling

  1. In Advanced Setup select Firewall.
  2. SPI: Enabled

Final area setting and check

  1. Click Interface Setup in the top-of-page menu
  2. Now select Wireless in the menu below that.
  3. Choose Canada for the Channel Setup
  4. Click SAVE

Still on this page, Verify:

  1. The SSID in the form NCF_XXXXX or as you set.
  2. The Auth Type is WPA2-PSK
  3. The Encryption Type is AES and key is DSL-Password
  4. Click on the Internet tab
  5. Ensure that PVC2 has VPI/VCI set at 0/35
  6. Ensure that PPPoE credentials are set properly for your user name and password.

The modem should now synchronize and connect to your DSL service if the service is operating. You may need to reboot the modem to get it to connect.

Security

In January 2014 it was revealed that some models of TP-Link modem, including this model, are subject to hacking if they are running out dated firmware and if the remote access (ACL) is set to allow remote access. This web page provides more detailed information on the vulnerability. Latest firmware versions can be checked on the TP-Link website.

ACL

  1. To be sure your modem is secure, click on "Access Management". By default the "ACL" tab will be active.
  2. Ensure your ACL page looks like the screen shot below. If not, choose "WAN" from the "Interface" drop-down box.
  3. Select "deactivated".
  4. Click "Save".

TP-Link modem with ACL deactivated

See also